(800) 853-2651
SHOP NOW

Recent content by 3588pfcred

Yesterday's Tractor Forums
  1. 3

    Early 1650 question

    My 1650 is a 1968 and its original and the tin by lights is white. Steve
  2. 3

    Plow advice for a 66

    3 uncle's had 70s and pulled. 2-14 , grandpa had a 66 and pulled 1-18 , when they plowed together the 70s would gain in the sand and the 66 would catch up in the heavy dirt. Steve
  3. 3

    Oliver 1850 hdyra power repair

    The engine needs to be pulled to remove the hydra power, if you have the ability to overhaul a engine, you can handle a hydra power if you have a good book. Steve
  4. 3

    1850 LP intake manifold

    Yes , John this is Steve
  5. 3

    1850 LP intake manifold

    30 miles west of Toledo , 2 miles south of 80/90
  6. 3

    1850 LP intake manifold

    I have a pair of LP manifolds from my neighbor's 1850 that I converted to gasoline my intake does not have that plate in the center that's welded or attached other than that they look the same. Steve
  7. 3

    1850 LP intake manifold

    I have LP manifold's from my neighbors 1850 that i converted to gasoline, the intake i have don't have the plate welded or attached in the center, other than that looks the same. Steve
  8. 3

    Hour meter

    Is the hour meter 6 or 12 volt, what is the tractor. Steve
  9. 3

    1970 656 Shifter Fix

    In the 70s I installed a few kits on the 656 tractors, not sure if the kit is available but it did tighten the shifting . Steve
  10. 3

    Detroit Oliver sighting

    I was at Yoder & Frey today there are two nineteen-hundreds the one for sure is a checkerboard Also an Oliver 60 a 66 with hydraulics a super 66 with hydraulics and a 77
  11. 3

    oliver1655

    On a 1650 if 6th is in the lower neutral it is high speed. Steve
  12. 3

    Building size?

    Before I built my shop in 2000 i worked at a caseih dealership, i asked 10 farmers that had already built shops what they would do different, (I was planning a 40x60 ) 9 out of 10 said that it would be larger, so i went to a 50x75 , if you are spending a lot of time out there heat in the floor...
  13. 3

    Oliver 1550 with Holley Distributor

    RTP has a new replacement copied off of a Delco with a tach drive that would work good, also korves sells them
  14. 3

    Pinion tool

    I measured the pinion tool i have. 1.8 in. Depth, i have seen that in a book, i think a 4366 Blue ribbon manual gives that distance, the 4366 pinion does not have the hole for the pinion tool. Steve
  15. 3

    806 smoking

    Has it been worked enough to seat the Rings
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top