(800) 853-2651
SHOP NOW

Recent content by 5000-nut

Yesterday's Tractor Forums
  1. 5

    5000 crankshaft help

    I have a 78 tooth crank that is bad but I have a 76 tooth crank that is good. If I change the balancer gears to match the 76 tooth crank will it work? 1965 5000 4.2 bore. Thanks for the information. Steve
  2. 5

    8n 3 point problems

    Thanks I will start there
  3. 5

    8n 3 point problems

    The only way arms go up is to hold draft control lever down. When they reach the top and the draft control lever raises about 1/4 of a inch and arms go back down but if you hold the lever down the arms will start to rise again. where should I start to look linkage in the top cover? Thanks...
  4. 5

    1970 2000 ford

    Gasser runs but not above 1200 rpm did all basic in ford Oem Manuel worked carb by hand and can go higher but gorvenor pulls it back.. Missing something small need some help input please thanks Steve
  5. 5

    Good price for wc 1941

    Thanks guys for the info. No steel on front only on rear. It's in Michigan friends dad passed and looking to sell, and I'm a ford / Oliver crawler nut so the allis I was not sure if it was a good price.. If any one would like to buy let me know. Thanks Steve
  6. 5

    Good price for wc 1941

    What is a good price for a 41 wc loose good tin on steel . Steel has low use. And a 39 frame rear end front end. They are asking 600 for all. Any input would be great. Thanks Steve
  7. 5

    Ford 7000 Smoke Around Turbo

    Look up Michigan turbo in grand rapids Michigan had one done 4 years ago $3oo out the door total redo nice work.. I will look for number if needed. Superior turbo in Ottawa lake mi 49267 [734]854-6900 is good to for turbos and injection pumps. My 5000 pump redone $450 I like them both hope the...
  8. 5

    1965 2000 governor

    I set the linkage to the ford book spec- but will not throttle up only 1200 rpms.. looked at gov- and did not see any wear.. The springs in linkage looks ok.. Run fine just won't throttle up.. Lost, need help.. Thanks Steve
  9. 5

    901 sos info

    My friend has a 901 sos in awesome shape (I have not seen yet) trans just stopped working.. I need info to find the right manual..I know naa and 4000/5000/7000 blue tractors very well,I have not done a 901sos. Where would the ID numbers be? any hints to get the right manual and buy would be...
  10. 5

    flat top fender paint?

    5600 flat top fenders they seem to be off white, gray/white? Is this right? If it is does anyone have a paint code, any brand.. I looked in the past threads and could not find a answer. Thanks steve
  11. 5

    air research turbo charger

    Michigan turbo Grand Rapids Michigan sorry I dont have the phone. Very good and prices are good.
  12. 5

    Ford disk ?

    I have a ford disk 10ft. Question is, I don"t know the model, all I have is series L and serial I677 or Ib77? Need to get some blades I think there 18 inch not sure its old? It is a wheel lift could not find any pic to help. Any input would help.. Thanks Steve
  13. 5

    bobcat boneyard

    Hey does anyone know of any boneyards for bobcat skider, all the one I know are fords ? Thanks Steve
  14. 5

    Did I just kill my tractor?

    Hey where are you? close to michigan? I have a 65 5000 sos new motor going to sell in spring for what I have in motor? Let me know if I can help..Steve
  15. 5

    ford question

    Hey I need help from you guys on finding ford disk blades. This is a hobby so I not sure if I used the right name for the cutting wheel. After market or OEM parts, whats easer to find. No numbers on disk but 10ft wide, I think 20" Dim. with 1-1/8 hole will take all help.. Thanks Steve
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top