(800) 853-2651
SHOP NOW

Recent content by 54robbie

Yesterday's Tractor Forums
  1. 5

    44 Diesel starter question

    The starter drive assembly blew up in my 44 diesel. They seem to be impossible to find. It is an Autolite MCK 4001 starter. Does anyone know of a supplier or a replacement part number?
  2. 5

    HD 260 Continental

    I am rebuilding an hd260 continental engine but I didn't pay attention to which way the pistons go on the rod. Arrow on the piston shows front but does the numbers on the rod face the camshaft?
  3. 5

    Bearings for Continental H277, H260

    I'm going off what i was told when I spoke to their parts department on the phone. They only service and sell parts for what equipment they sell. "None of that old stuff", is what i got told. and BTW he was not polite about it either.
  4. 5

    Bearings for Continental H277, H260

    This outfit only deals with the newer stuff, nothing old.
  5. 5

    Vibrator coil

    How did you mount it? Got any pics?
  6. 5

    Vibrator coil

    If the coil in the original is bad how are you getting power through to the vibrating contacts? Did you gut the coil from the original and run direct?
  7. 5

    Vibrator coil

    How did you go about it? Can you share some pics?
  8. 5

    Vibrator coil

    Here are some pics of the actual thing.
  9. 5

    Vibrator coil

    This is out of the parts book. #52 top left corner.
  10. 5

    Vibrator coil

    Has anyone found a replacement for the vibrator coil for the manifold heater on a 44 diesel? Or what have others done when this thing goes bad?
  11. 5

    k-d lamp vs guide lamp

    Will a Guide lens fit in K-D lamp housing if they are the same diameter? Is the lip on the lens the same on both?
  12. 5

    UTS gas engine rebuild

    Email sent Chris.
  13. 5

    UTS gas engine rebuild

    I did hear somewhere that g900 pistons were used with a little machining. Am I totally off base?
  14. 5

    UTS gas engine rebuild

    What other engines used the 4 1/4 bore like the 283. I'm needing some oversize pistons for mine. Have any of you folks done that and what machining was involved? .020 over is what I need for pistons. Thanks.
  15. 5

    W6 clutch specs

    Just to clarify, this is not a new replacement clutch nor is it a worn out one. This one was installed years earlier by somebody that didn't know what they where doing. Everything is still in really good shape. Thanks for the Blue Ribbon manual.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top