(800) 853-2651
SHOP NOW

Recent content by 560gaspuller

Yesterday's Tractor Forums
  1. 5

    ih six cylinder head

    murphys motor service, they have the whole valve kit, im doing the same to my 301 right now also.
  2. 5

    farmall compression

    is 165-170 pounds good for a 301? stock as far as i know thanks
  3. 5

    460 pto removal

    Nope, thats all you gotta do, make sure you get a shaft out too, about 2 feet long, (-/+) some. cut a piece out drill out holes silicon it up, and bolt it on, Good to go! hope this helps.
  4. 5

    farmall 460/560 Puller options

    i pull a 560 with a 301 i pull mph classes usually #5500 4 mph and #7000 up to 9mph, i usually place in top 3. 18.4-34 tires.3rd gear. hope this helps you some.
  5. 5

    H Countershaft Oil Seal Question

    im doing this on my h right now., remove the 4 tapered bolts that connect the input shaft to transmission. then the 3 bolts that the seal sits in, them remove the bolt from the center of input shaft. Easiest is to put the tractor in gear so it dosent spin on ya. hope this helps
  6. 5

    1939 B weight

    my buddy has a 39 b butit has pressed stee, he gets it in 3000 if he finds a kid to drive, hope this helps,
  7. 5

    9 bolt hubs

    Buy cap bros hubs.i bought a set for my 560, best invesment i made!
  8. 5

    560 pulling

    if the pulls around here would allow turbos in my class, i would for sure! that would be sweet!
  9. 5

    560 pulling

    will be putting a silver diamond head on my 301 motor in my 560 this winter.should a get a cam ground, who is good? also will i need a bigger carb?
  10. 5

    New Richmond FFA Alumni Antique Tractor Pull 9-28-13

    i hope it dont rain. Im looking forward to the last pull of the year!!!
  11. 5

    560 compression

    should i get a cam out of the motor i got the head from?. or get a combine cam? thanks
  12. 5

    560 compression

    who should i have grind my cam?.
  13. 5

    560 compression

    will i still be able to run pump gas?
  14. 5

    560 compression

    what will my compression be with a 301 stock motor with a silver diamond head?.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top