-
7
..any ideas for a simple counter weight? 2 to 300 lb maybe
tractor wheel weights on 3 point frame -
7
Need help! Big Bee Gear Box Oil - How to Check/Fill
1/8" pipe plug at 4 oclock on back of gear box oil level plug- 714_run
- Post #4
- Forum: Tractor & Farm Talk
-
7
861 lift/hydraulic issues - always drifting up
internal linkige adjustment could be wrong. could pull top cover and re ajust. or pull side cover with dip stick an using 2 7/16 wrenches try re ajust the lower linkige unlock jam nut turn longer nut one turn shorter -
7
Looking for an Elenco 4wd front end - Tony Jacobs contac
This message is a reply to an archived post by TONY JACOBS on November 21, 2013 at 22:34:09. The original subject was Re: Looking for an Elenco 4wd front end Tony Jacobs contact me. my torque limiter is mounted on the tranfer case. what is proper way to use the disconnet bolt head on the back... -
7
power steering issue
pump is not a vane pump or a gear pump more like a roller bearing pump 800psi. for 821 need two cyl. they are one way cyl. one pushes the other -
7
871 PTO output seal replacement
I have changed pto seal by drilling a small hole in the seal screwing in a metal screw and using a nail bar to pry it out ( had to try several times- 714_run
- Post #3
- Forum: Tractor & Farm Talk
-
7
Ford 640 STUCK CLUTCH Situation. What to do to free it u
hold clutch pedal down engine running pop it in high gear -
7
Leaking water temp sensor, help please
take a lock washer twist it open put around the tube twist it back flat tighen the nut against it- 714_run
- Post #1
- Forum: Harry Ferguson
-
7
Super C - Idiot light:)
one wire system news high rpm to start charging- 714_run
- Post #1
- Forum: Tractor & Farm Talk
-
7
hyd cyl end cap removel
Trying to get end cap off 3 " hyd cyl. to spanner holes in face of cap. used 4 foot cheater pipe & air hammer no joy what next can I use a torch to heat the end of the cyl.- 714_run
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
7
IH 100 balanced head sickle mower
looking for 10 & 3/4" dia. drive pulley with slip clutch hub thanks- 714_run
- Thread
- Replies: 1
- Forum: Tractor & Farm Talk
-
7
eng knock crank shaft end play
yes a lot of crank end play can cause a knock- 714_run
- Post #1
- Forum: Harry Ferguson
-
7
3 point hoe
I have a three point backhoe with a frame mount and a pto pump for my four cylinder Ford. The backhoe works fine and is in good shape. The problem is the wiper seals on cylinders are shot. Do they make a split wiper I could put on without taking the cylinder apart? (Wishful thinking?) I hate...- 714_run
- Thread
- Replies: 1
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy