(800) 853-2651
SHOP NOW

Recent content by 8n/9n

Yesterday's Tractor Forums
  1. 8

    shop air lines

    Hello, I am plannig on installing an air line around the shop to the different bays and to the benches I was wondering what size line and what type of line to use to make this system work correctly and without spending to much money. I would just like tips on what others have dibe and their...
  2. 8

    DUMP TRUCK HYD. CYLINDERS

    With my uncles truck (a 10 yd mack CH612 6 wheler) it has a 3 stage single cylender, the only problem we have with this one is that if it goes all the way up when you lower it it will slam down a few inches at the top.
  3. 8

    craftsman

    I was wrong. A real quick check to a site on this amazing world wide web of ours reveals that sears did buy k-mart. I was wrong. Untitled URL Link
  4. 8

    craftsman

    Not that it matters, but I think that k-mart bought sears. I could be wrong, but I think that k mart owns it all now.
  5. 8

    CNH Global

    When I bought the new ford parts for my 9N all the boxes said CNH Global, This stands for Case New Holland? So IH, Case, Ford/New Holand are all the same company? When did this take place? Thanks, Ben RI
  6. 8

    charging system and ignition question.

    I am going to instal an alternator, a 12 volt battery and a 12 volt coil soon, what I wantto know is wheather or not I can fins a resister without buying that kit with everything from this site becauseI want a 1 wire alternator. So What I want is a radio shack or napa part number for the...
  7. 8

    adding a proofmeter

    How could I locate the proofmeter shaft on the govoner.
  8. 8

    adding a proofmeter

    Hi, I have a 9N and it has an 8N engine in it. With a side mount Distributor. I would like to know if it is possible to add a proofmeter to this tractor and how much work is it to do it. Thanks Ben
  9. 8

    3 point setup

    Can anyone provide me with some pictures or a diagram of the 3 point setup on the 9N? Thyanks, Ben
  10. 8

    john deere help

    I don"t know whether you know JD"s that well, a JD is a 2cyl anot a 1,3or 4 so it idels differently. Like mattd said it only fires at 180 and 540 degrees because of it being a 2cyl. if you are more expirienced with tractors than me and I sound like a condesending jerk, I am not.
  11. 8

    L778 New Holland Skid Steer

    What are the hours and how old is it. Last winter I helped instal a new final drive in a compact excavator, it is about $1200 for that motor, I do not know how much itg would be for that but it cant be much less. But we need the hours and the age to make an estimate.
  12. 8

    Ethanol

    So using stabil will help the gas keep?
  13. 8

    Ethanol

    In my part of the country pure gassoline is hard to find it all has a certain ethanol content that will screw with seals in certain motors how will ethanol effect the tractor, will it eat away at the seals or is it safe to be used. The other question is how long it will last in the gas tank just...
  14. 8

    !2 volt

    I have a ford 8n motor (in a 9N) and after re evaluating my situation I have decided that a 12 volt conversion is in order. What I want to know is what I will need to do about the coil and the electronics in the distributor. Do I need to replace either or both of these things when I instal the...
  15. 8

    What sized plug for 8N

    ok, thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top