(800) 853-2651
SHOP NOW

Recent content by A. G. Keiper

Yesterday's Tractor Forums
  1. A

    148 159 case swap

    They should swap just fine. The issues that you have to watch for are: 1) the length of the engine block, distance between bell housing and front housing, 2) spacing between the two big top bolts in the bell housing, 3) how the engine oil filter is configured on the block. It should be...
  2. A

    Got a new tractor and started another project

    Jon, I don't know what you'll decide to do, but if you need it, I have a NOS ring and pinion set for sale. $400 in Ohio.
  3. A

    Look What I Found!!

    Great video. Thanks for finding that, John. My brothers and I got to spend some time on several of those Case combines back in the 70's. Even got a chance to use a 1665 here in northeast OH.
  4. A

    1150b trans pressure

    What you are seeing is basically normal; I'm not sure about the exact numbers, but you would have to have everything warmed up to be exact. The 30 psi is lube pressure when the clutches are in neutral. In order to build pressure both forward/reverse levers must be engaged.
  5. A

    RC governor

    Marshal, Governors can be a little tricky, and you always wonder if yours is working as well as they ever intended to work. I have an owners manual for an R tractor and it explains how to adjust things on it, but not much information about trouble shooting. I do have a brand new one that looks...
  6. A

    Needing baler parts

    I have those sweep feed fingers and the pads new and a used pin and snap ring.
  7. A

    Help with engine identification

    Do your injectors go into the side of your heads or are they on top next to the valve covers?
  8. A

    Need a little help with brake shoe direction - 1952 Case VAI

    As you can tell, I used a hammer and chisel to remove the drum I sent to you. I think I tried a long 3/4 drive ratchet on there, but was not able to keep the shaft from turning enough to break it loose. From your picture, it looks like your bolt might have more rust than mine did. A method that...
  9. A

    Jack Pad and Base

    Check with Jerry Sanders. Email [email protected]
  10. A
    Expired

    For sale Case 300 transaxle

    can load 330-four16- four six 82
    $250.00
  11. Combine tire
    Expired

    For sale Combine tire

    50% tread, can load 330-four 16-four six 82
    $75.00
  12. A

    oil pressure relief valve

    It's on the oil pump. Have to remove the oil pan. Did someone put a pump from a diesel engine in it? They run about 80 pounds pressure.
  13. Case 300 round nose bolster and dual wheel front pedestal
    Expired

    For sale Case 300 round nose bolster and dual wheel front pedestal

    can load 330 four one 6 four six 82
    $180.00
  14. A

    Case 300 push rod tubes leaking oil.

    Oops, I didn't realize that the early heads, the VAC and early 300, had no o-rings. I thought all those heads with push rod tubes were the same. I guess all the ones I have worked on were either 148B or 159 engines.
  15. A

    Case 300 push rod tubes leaking oil.

    Those tubes have been a trouble spot on any Case small block gas head for years and those early VAC engines are 80 years old. The best time to replace them is when the head is off for a valve job and the tubes are somewhat cleaned. The o-rings are standard dimension, but make sure you get good...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top