(800) 853-2651
SHOP NOW

Recent content by Abbby

Yesterday's Tractor Forums
  1. A

    9600 electrical schematics

    Worked on a 9600 today that I know little about. Starts and runs by applying power direct to starter. Does not turn over with key. Wiring is a mess down by the starter. Not sure where the yellow wire goes or what the small little electrical box is circled in red. Anyone have knowledge of this...
    • Abbby
    • Thread
    • Replies: 1
    • Forum: Ford
  2. A

    Cam removal Ford 800

    Which means tractor must be split
  3. A

    Want to buy a 9N What should I look for?

    Unless you are getting it for free look for an 8N, Jubilee or hundred series.
  4. A

    1951 8n hydraulic pump

    You can buy from this site. Many videos out there on the pump rebuild.
  5. A

    Which battery for 12 volt conversion?

    Once you figure out size go to Walmart
  6. A

    Finally getting my 2N to limp around.

    Did you try adjusting the idle and main jets?
  7. A

    Ford 4000 delux contor seat adjustment

    I have the earlier version as Ultradog has shown in pics. It has no spring suspension at all. Feels just solid. Tried adjusting with the threaded rod but seems to have no affect. Is something worn out that I can replace or am I missing something?
  8. A

    8N turns over but won’t start

    You need good spark that can jump 1/4" gap and the correct amount of fuel. There are three fuel filters in the system. One attached to the fuel shut off and its inside the tank. The screen on top of the fuel bowl and a screen inside the carb attached to the fuel inlet. Check and clean the two...
  9. A

    Spark plug wire tube

    Agree with Tim. Take the tube off the tractor and feed the wires thru using some dry lube or other. Do not have the ends on when feeding them thru. Put the distributor end on after fed thru.
  10. A

    Ford 8N clutch replacement

    Lets get real here. This is not a 2-3 hour job for most people and a novice more like 8-10 hours. I have done lots of mechanic work and I would say its a 6-8 hour job.
  11. A

    How many folks are "loving" this new site update?

    Same people complaining about the new site also do no understand why anyone would want spin on oil filters, 12 volt system and electronic ignition. "Your living in the past man"
  12. A

    Compression test results

    It if starts and runs good then leave it alone.
  13. A

    Compression tester recommendation?

    JB weld might work. No need to apply that much torque to seal.
  14. A

    changed the oil in the 9n and found these

    Wires to secure con rod or main bearing bolts?
  15. A

    Ford 3000 hydraulic pump

    Rest of the story. So mine does have the bigger side plug. Kind of down lower and did not see. Loosened plug and injected 20 psi into differential housing while tractor was running. There was a slow drip drip out of the plug. It took a quite few minutes to prime. I was almost going to give up...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top