(800) 853-2651
SHOP NOW

Recent content by ajco

Yesterday's Tractor Forums
  1. A

    Who can tell me about 7580 Allis

    sorry= that engine speed should be 2500
  2. A

    solid front tires? AC - ca

    I used front steel wheels off manure spreader
  3. A

    Who can tell me about 7580 Allis

    Igot 1 in 1981. approx. 9000 hrs. now.Not used much last 8 yrs. have 350 hp. Steiger to dowork now &most of farm is rented out. 1st replace crank balancer on crank pulley & every 1500 hrs. ( breaks crank when it goes bad)I have only replaced u joints once. reduce engine speed to 1500 ^ it...
  4. A

    hard to start poulan pro chainsaw

    I have an old well used Stihl026 { we heat 2 houses with an outdoor wood burner} that always took10 pulls to start from day 1 if left over night but 1 pull when using.I took it to dealer this fall for check up - crank seals, carb. filters etc. When it came back it took 20 pulls to start. Dealer...
  5. A

    using a tractor to pull or haul logs safer

    put a pair of tines on top ends of bucket parallel to the bottom tines so you dont get a log on your lap if the loader accidentally goes all the way up when you are looking elsewhere & something catches the loader control.When cutting evergreen trees~the branches may act like springs when the...
  6. A

    nuther interesting tool

    To make these punches even more useful - drill a dimple in the big end to keep an air hammer punch in place when you are working by feel only & no room to swing a hammer.
  7. A

    snake problem

    Bury end of pipe in a foot or more of gravel
  8. A

    replacing spindle bushings?

    pull axle out of square tube.Turn over& put back in. support with good solid block.drive off steering arm. heat helps.remove old bushings with chisel or punch . put a new bushing on spindle & drive into tube repeat with other bushing,
  9. A

    Grease gun

    When gun air locks unscrew nozzle pipe or hose & pump handle to remove air & get grease again .
  10. A

    Rat Proplem

    yellow or blue fly bait & coke -doses coons too
  11. A

    schwart spindle

    google -Eldale machine &tool 3Industrial drive Elmira ontario Canada N3B 2S0 519 669 5195
  12. A

    Is a camera a tool?

    pull battery. put back in. charge until 3 lights on top of camera are lit.
  13. A

    generators not charging enough

    Remove brush cover. Loosen screw in end of generator. Pry brush holder against rotation to increase charge.Tighten screw.
  14. A

    C starter grinding

    Forgot- Remove spark plugs&turn engine by hand while holding starter in to be sure starter gear clears ring gear. Use soft ni- rod to weld hole full . Keep cool enough to touch. ni-rod available in small packages at TSC. Make tapered hole with ground drill bit or tapered reamer or carbide...
  15. A

    C starter grinding

    Remove tapered mounting stud.If starter will push in-remove & weld nose stud hole full.Replace & mark where hole needs to be.Drill new hole in cone with bit ground to make tapered hole.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top