(800) 853-2651
SHOP NOW

Recent content by Al King

Yesterday's Tractor Forums
  1. A

    Holder C9.78H

    Hi Jim, I am near Waubaushene Ontario Canada. I have lots of experience working on many different makes of tractors. This one is a little different. There doesn't seem to be information on it.
  2. A

    Holder C9.78H

    I have a Holder tractor that we use for snow blowing. My problem is that it won't reverse. There is a switch on the handle that selects either forward or reverse. There must be a solenoid operated spool valve or something like that to make it change direction. I can't find any information about...
  3. A

    Wisconsin 2cyl (THD) valve guides.

    I am working on a Wisconsin THD that happens to be in my lawnmower. The valve guides seem worn to me, you can move the valves about .020 sideways. My question is, would it be acceptable to bore out the valve guides and install new ones made from brass. I have a vertical mill and a lathe so no...
  4. A

    Ford 7710 Alternator troubles

    I checked the output voltage and it's 14.2 so I'm going to leave it alone. The alternator that was sold to my neighbours from New Holland has the label SPS and the part number 165-27108. It's 12v 70 amp and made in China. They were stuck with it, New Holland wouldn't take it back. If it was my...
  5. A

    Ford 7710 Alternator troubles

    I offer this as it may help others. My neighbours have a Ford 7710 tractor. The original internally regulated Lucas alternator failed and a new replacement was purchased from New Holland. The replacement is a SPS with little or no installation instructions. It mounts correctly but they couldn't...
  6. A

    8N Newbie brake question

    Thank's Mark, This is my first time working on an 8N so am no expert. But I have worked on lots of other machines. My 8N is a 1950 and it does have inner seals. I replaced the seals and they fit well on the axle shafts. It doesn't make sense to me to put an inner seal if you want gear lube to...
  7. A

    8N Newbie brake question

    We have new neighbours who asked me to remove an old tractor that was back in their 50 acres. It turned out to be an 8N. It had about 2 inches of moss on it so it had been there for a while. They gave it to me and I stuck it in the back of one of my sheds. So for the heck of it, I checked it...
  8. A

    MF 65 Diesel breaking starters

    When I got this tractor it was running, but had a knock in the engine and low oil pressure. I tore it apart and found that the No 4 rod bearing was gone and had scored the crank. So I put a new crankshaft and bearings into it. I replaced the rod with the spun bearing with a new one. Also put in...
  9. A

    MF 65 Diesel breaking starters

    I have a MF 65 with an indirect injection 4 cylinder perkins. The back plate on the starter was broken when I got it. Replaced it and it broke again. Pulled the starter all apart and everything looks good. Could it be caused by the fuel injection pump timing being too far advanced. The tractor...
  10. A

    George White snowblower gearbox

    I have an old George With 7 foot snowblower, The gearbox cast iron casing is broken beyond repair. The box is a Durst A11, and so far as I can tell is no longer available. I did find a usable gearbox in another old blower. It's made by Dana and has a number 40 cast into it. I can make it fit by...
  11. A

    George White snowblower gearbox

    I have an old George With 7 foot snowblower, The gearbox cast iron casing is broken beyond repair. The box is a Durst A11, and so far as I can tell is no longer available. I did find a usable gearbox in another old blower. It's made by Dana and has a number 40 cast into it. I can make it fit by...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top