(800) 853-2651
SHOP NOW

Recent content by Alex759

Yesterday's Tractor Forums
  1. A

    Slow hydraulics

    Thanks
  2. A

    Slow hydraulics

    I have a Ford 4500 tractor with a Ford 755 backhoe attachment. Transported it from Alabama to Nevada last Fall, everything worked great. This Spring the hydraulics are very slow to respond (all work but take 30-60 seconds to move. Fluid level is okay, and I do not appear to have any external...
  3. A

    Flasher

    Take care that the flasher meets the type of light you have. I have made the unfortunate mistake of using a flasher intended only for LEDs on my old incandescent ford......
  4. A

    Ford 4630 Diesel (no cab)

    Thanks, found that out on my truck. I have had pretty good success with stainless steel ones from harbor freight. I have also considered marine wire with the sleeve. Not sure if there is any sleeved automotive wire.
  5. A

    Ford 4630 Diesel (no cab)

    I can buy a lot of wire on the internet for that..... Any recommendations for sleeve material? The metal sleeves have all corroded away. I thought about PEX but don't know how well it would hold up. This post was edited by Alex759 on 03/19/2022 at 11:54 am.
  6. A

    Ford 4630 Diesel (no cab)

    Cleaning up the numbers to make them readable.
  7. A

    Ford 4630 Diesel (no cab)

    When in neutral is the switch open or closed? There is a relay plug behind the instrument panel but w/o a relay in it.
  8. A

    Ford 4630 Diesel (no cab)

    Thanks for the info. I have the starter working, have to order a neutral switch. I have a wiring diagram, but the colors don't match what is inside my tractor, but it starts and the lights work. so far, so good.......
  9. A

    Ford 4630 Diesel (no cab)

    Thank you for the info. I needed the wire gauge that actually energizes the solenoid. The neutral safety switch is currently disabled. On my list..... Does it go on the solenoid side or the relay side of the tractor? Thanks Alex
  10. A

    Ford 4630 Diesel (no cab)

    I have to redo wiring from the key to the solenoid (have a short, one of the wires is grounding). I plan on running Hot>fuse>key switch>control relay>ground. What gauge wire is needed for the control circuit (positions 85 to 86)? Also, what gauge wire to actually energize the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top