(800) 853-2651
SHOP NOW

Recent content by AMB(WcIL)

Yesterday's Tractor Forums
  1. A

    Allis forum

    Has been down several days. Andy
  2. A

    Allis XT190 vs 200 transmission and rearend

    Yes, the 190XT Series III and the 200 had the most updates in the rear. I'd say by now most all the 190's that have survived this long have had the updated rear ends. The real early production tractors had smaller axles as well.
  3. A

    unofficial allis page

    Anyone else having trouble getting logged on this week as well?? Week of July 20th?
  4. A

    unofficial allis page

    Yep, it doesn't open up me either. I noticed it yesterday 6-10.
  5. A

    How many have bought the same tractor twice?

    Back in March I found the first tractor I bought when I was 19 yrs old. A 185 Allis Chalmers with a Allis Chalmers loader. I recognized it in a picture on a online consignment auction 70 miles away from home. I bought it in October 1993 and traded it off for a different loader tractor in...
  6. A

    Favorite Antique Tractor for Rides/Drive

    My favorite tractor for cruise's is our 1964 Allis Chalmers D-15 series II High Crop. Tall tires for faster speeds and the Big Stick for on the fly shifting climbing hills. My 2nd choice would our 1975 Allis Chalmers 200 with factory cab. Andy
  7. A

    8550

    Yes we still use one for fall chisel plowing. It has been repowered with a Mack truck 6 cylinder engine. Our road district used it last summer to pull a sheep's foot. Andy
  8. A

    Info on 1020 IH heads

    Yes you can bolt a little plate with two 1/2" carriage bolt to make a 1020 head ridged.There is a pin on the wobble box end you have to use to lock it up. I believe 1020 header sizes are 13'-30'. I've had a 20' and a 30'. Now I run a 2020 30'. The 1020 series is a better head than the 2020...
  9. A

    band duals

    You are missing a upside down U shape piece that has a peg that goes in those holes, it has a larger hole for the J bolts. Andy
  10. A

    JD 756 tedder ?

    I think you need to remove a bolt mid way up to check level. I use to have a JD 754. Andy
  11. A

    4240

    Sounds like load shaft seals are leaking. Probably need to replace the shaft and seals.
  12. A

    AC 200 any weak points

    200's could have dual pto speeds. 540-1000 rpm.
  13. A

    Here I am with another not an antique

    My 7410 JD, had same kind of cold start advance. Last summer it went bad and was shorting out the solenoid at the injection pump. The Deere Tech unplugged it and all is well now. Andy
  14. A

    Allis Chalmers 190xt series 3

    Sounds like the governor flex-ring in the injection pump to me. Andy
  15. A

    A-C 190XT

    No, The best way to get apart would be unbolt the front weight/pivot from the frame rails and roll forward. I have never had very good luck trying to pull the front axel pivot pin.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top