(800) 853-2651
SHOP NOW

Recent content by Andy Moore

Yesterday's Tractor Forums
  1. A

    allis 160 tractor

    I inherited a 160 from my dad in 1992, which worked great until a couple of weeks ago when the clutch froze up. The shaft won't turn, and I broke the rod trying to adjust the nut. Does anyone know if parts are still availabe? You don't see a lot of these. thanks.
  2. A

    Float for 1969 Ford 2000 Holley carb

    Just a final note. The Holley R3589B still wouldn't work right after the servicing, and I replaced it with a Zenith 13914A (EINN9510DA). If anyone wants the old carb, let me know.
  3. A

    Float for 1969 Ford 2000 Holley carb

    Appreciate all the replies. The pinhole leak was at the factory plug, so I melted out the solder, then heated with a blowdryer (gas all came out in a couple of minutes!) and resoldered the hole shut. Now, let me ask again- how do I set this float? Does anyone know the correct spec, and where to...
  4. A

    Float for 1969 Ford 2000 Holley carb

    Have you ever tried permatex gas tank repair epoxy (comes in thin strips you knead up and apply like bubble gum)? Sticks to gas-wet metal. I'm not real confident about soldering on this. What about clear nail polish for the pinhole leak? Used to use it to seal around welch plugs in chainsaw carbs.
  5. A

    Float for 1969 Ford 2000 Holley carb

    I may try repairing this if I can't find a good one. Another thing wrong with the float is that the two chambers are not aligned. Holding the carb body upside down(float and needle installed), one float chamber clears the gasket and the other is just below. Do you know the correct setting? Is...
  6. A

    Float for 1969 Ford 2000 Holley carb

    Dean, I printed out the 09D01 illustrated parts list from CNH, float is C5NE9550A. Are you sure that this is still available? Every part description here says "no longer serviced." Also, how important is the little float pin spring? This was missing from my carb. thanks
  7. A

    Float for 1969 Ford 2000 Holley carb

    I just took my Holley R3589B apart, cleaned every passage, freed up the pump (plastic retainer was on the wrong side of the gasket), but I'm stumped with the float. There's liquid inside one of the chambers, and nobody stocks this part anymore. Anyone have an idea on where to find a used one...
  8. A

    Ford 2000 coil wire burnt in two

    Thanks for the replies. It was the little wire to the distributor. I found the nut loose at the points (wire burned to there), replaced the wire, still no fire. Will replace coil, points and condenser. What should the point gap be? Looks about .035 presently. What do you think of electronic...
  9. A

    Ford 2000 coil wire burnt in two

    What would cause the wire from the coil to the distributor to burn up? This tractor was missing badly, cutting out when you speeded the engine up from idle. thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top