-
A
Cutting Sheet metal
That angle grinder is extremely dangerous and should never be used. A year ago I cut the back of my hand open with one to the bone , severed tendons, had surgery to re-attach tendons, was one handed for three months and have permanent loss of motion in my hand. Do not use a grinder like that no... -
A
What's it Worth?
Where are you located? Might be interested in the regulators. -
A
Have I missed anything needed to make a WD45 pull
Can you flip the draw bar over to get you to 18" and still be level ? Or shim the clevis with washers ?- andyinct
- Post #1
- Forum: Tractor Pulling
-
A
Mag drive bearing
Does anyone have a source or part number for the bearing in the block for the mag drive on a Farmall A ? Thanks- andyinct
- Thread
- Replies: 3
- Forum: Farmall, International & McCormick
-
A
Farmall A timing marks.
I have to look again - I know there is two dots on the cam gear but I think only one on the crank. There is a single dot on the cam gear that was one tooth off the mag gear. That is what lead me to investigate further.- andyinct
- Post #1
- Forum: Farmall, International & McCormick
-
A
Farmall A timing marks.
I am working on a Farmall A - repairing the governor. I noticed the timing mark on the cam and governor drive was one tooth off. So I took the timing cover off and the cam and crank was one tooth off. I want to confirm that two dots on the cam go to one dot on the crank. Is that correct? Thanks- andyinct
- Thread
- Replies: 2
- Forum: Farmall, International & McCormick
-
A
Wood Chipper Question
I have a Machete chipper - bought it 30 years or so ago. Works great for what I do. Not going to set any speed records or use it for a tree business but will chip up to 3 inch. It is now made by a Chinese company - Jinma I think. That is how I get replacement parts.- andyinct
- Post #1
- Forum: Implement Alley
-
A
I've had it!!!!!!!
I just bought a Miller 211 - good little machine. -
A
Allis C problem
At one point I took the sediment bowl out and had a elbow and inline filter and it was doing the same thing. So I put the sediment bowl back on and same thing. The tank is clean.- andyinct
- Post #1
- Forum: Allis-Chalmers
-
A
Allis C problem
This problem has been going on for a while. I have an Allis C that I pull with. High rpm - get down the track a ways it starts to quit like its running out of gas. If it stalls it starts right away. I have a fuel bowl on it - 1/2 line to carb, cleaned the carb, had mag rebuilt, still doing it...- andyinct
- Thread
- Replies: 7
- Forum: Allis-Chalmers
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy