-
R
Hey Fixerupper!! RE: JD RW disk
Fixer. I would like to talk to you about the parts I need for my JD RW disk. I live near Albia in se Iowa. Please e me or call 641-932-8049 Thanks, Randy G- Randy G
- Post #1
- Forum: John Deere
-
A
No-Till Corn after 1st cutting
Need advice; have any of you no-tilled corn into a alfalfa field after you have taken off the 1st cutting. How do control the regrowth of alfalfa is my main concern, advice is greatly appreciated.- Anonymous-0
- Post #1
- Forum: Using Your Tractor & Crop Talk
-
A
D17 Power Director
Last Summer I bought a D17 and the owner told me upfront the PD didn't work right. He had it "blocked" in high side with the control lever tied in position. The man was very honest and I have no complaints with him. After getting the tractor home I found there was not enough fluid in the PD to...- Anonymous-0
- Post #1
- Forum: Allis-Chalmers
-
A
641 starter problems
It works....thanks a lot John in LA. Sorry it took a while to respond but I was down for a couple. Once again thanks a lot.... Art -
A
641 starter problems
Thank you for a quick response. It seems that just when I need it most, it's not working. The tractor started before by a turn of the key switch, and it worked before I fixed it? I changed the starter for the wrong reasons. My problem I've been told is that I have missing teeth on my fly wheel... -
A
641 starter problems
Thank you for a quick response. It seems that just when I need it most, it's not working. The tractor started before by a turn of the key switch, and it worked before I fixed it? I changed the starter for the wrong reasons. My problem I've been told is that I have missing teeth on my fly wheel... -
A
641 starter problems
I have a 641 that was converted to 12 volts. I am not a mechanic but I like messing with my tractor. Here's the problem, I removed the wires to the solenoid and the starter switch, when I replaced the starter, but lost the paper where I drew a diagram of where they went. My ignition has four... -
A
GAS TANK VALVE ON 641
Hey 36 Coupe, I read your response where you said don't use "MMO". I don't know what "MMO" is. I just put a gas valve on my tank because it didn't have one when I bought the 641. I am learning from your experience and the other helpful people on this site. I don't want to run into a problem... -
A
641 Fuel Line / Sediment Bowl
Wagonmaster, thanks for your input but, what do you mean start the line on the sediment bowl before connecting it to the carburetor? -
A
641 Fuel Line / Sediment Bowl
Noob, I currently have a gas filter on it but I was going to go back to "as original as practical". What is the difference between the filter and sediment bowl? I thought that the sediment bowl was a filter of sort using a different method. I may have not mentioned that I am not a mechanic, I... -
A
641 Fuel Line / Sediment Bowl
Thanks, do you have a schematic of the way the fuel line runs? I can purchase the steel lines and bend them the way they need to go, but I need the two lenghts. One from the tank to the sediment bowl and the other from the sediment bowl to the carburetor. Where does the sediment bowl go? It... -
A
641 Fuel Line / Sediment Bowl
I have a 641 and it runs good, but, I have a rubber gas line that leaks and rests on the engine. I see photos here and see that the 641 actually had ridgid (metal / copper) lines from the gas tank, to the sediment bowl and finally to the carburetor. I need to replace the current line and want... -
A
641 PTO / 3 Point ?
What I am calling the PTO is the splined shaft at the back of the tractor. There is a two speed lever on the side that can only be engaged when the clutch is pressed down and does not operate until I release the clutch. If I push the clutch in, it stops turning. This rotates my bush hog. Is... -
A
641 PTO / 3 Point ?
I have a Ford 641 tractor that I got as a project tractor. I want to restore it as much as possible but it also has to earn it's keep around the place, i.e. bush hogging, tilling, grading, etc. By reading this forum I got it running and have figured what everything does and why it does or... -
A
641 Ford Tractor
Thanks alot everybody for your help I'll try it out today. I was wrong though, it moves from pointing towards the radiator or front of the tractor; to straight down towards the ground....of coarse, not being a farm raised person I don't know what "draft" is!!!! Thanks again for your response.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy