(800) 853-2651
SHOP NOW

Recent content by Bansheetaz

Yesterday's Tractor Forums
  1. B

    Farmall 300 pertronix ignition

    Heres new info... black and red wires are for negative ground systems.... black and black w/white stripe are for positive ground systems. So the points will go back in after i figure outhow to keep oil out of the distributor. Thanks for all the good conversation
  2. B

    300 hydraulic fluid in distributor

    This piece
  3. B

    300 hydraulic fluid in distributor

    Im guessing here thinking the seal responsible for this is on the distributor drive side of the hydraulic pump. How do you get the distributor drive flange off the pump so you can access the seal. It must be pressed on there and pretty hard to get anything in there to pry it off. Ive got...
  4. B

    Farmall 300 pertronix ignition

    Sounds like what im going to to. It ran ok with the points anyway.
  5. B

    Farmall 300 pertronix ignition

    I was kinda thinking this as well and you are probably correct. I got them in a box of old farmall parts on an auction and was told it was all for 12v stuff but the numbers had me suspicious but had nothing to lose trying them.
  6. B

    Farmall 300 pertronix ignition

    I dont know. When i got the tractor the coil felt pretty dang hot and with the resistor its not as hot. I think it was omitted when it was converted to 12v originally.
  7. B

    Farmall 300 pertronix ignition

    Howdy. Trying to install an electronic ignition in my 300 rowcrop. I must be missing something as i cannot get spark. Its a 12v system and i have a ballast resistor inline to the positive side of the coil. I have 2 ignitors shown in the attached picture. Are they for 6 volt systems? I was...
  8. B

    Head bolts and nuts. Farmall 300 vs H

    Anyone know if the head studs and nuts are the same for these tractors? I need a couple studs and nuts for a 300. Thank you
  9. B

    Farmall 300 head gasket

    I found the cylinder sleeves to be too high. I'm going to get the block all taken care of and it should be good to go. . Thanks for the suggestions
  10. B

    Farmall 300 head gasket

    What brand of aluminum paint would you use. Is that something home depot would have? I've got several torque wrenches. I'm going to check the sleeve height as well. Thank you for the help
  11. B

    Farmall 300 head gasket

    Yea i was planning on using a different one this time. Thank you
  12. B

    Farmall 300 head gasket

    I had the head milled last time and checked the block for straightness. All looks good. No pitting anywhere. The gasket has several spots where the material has pushed out from the sealing ring. Which looks like not enough torque. And before I disassembled this time I found several...
  13. B

    Farmall 300 head gasket

    Well I need to replace the head gasket again on my 300.. 3rd time in 2 years. So now I'm looking for advise First.. is felpro ok to use on these? I've used them with great success on many cars and trucks with no failures. Or is there a more preferred gasket. Second... the gasket...
  14. B

    Hesston 540 baler

    I took the valve apart and cleaned some crud out of it. The lift arms work better but it still doesn't seems like the tensioner is working right. Although I did have the belts undone. Im not sure it's plumbed correctly.
  15. B

    Hesston 540 baler

    Ok would there be a hydraulic schematic available anywhere? I ordered a manual. I hope that's in there
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top