(800) 853-2651
SHOP NOW

Recent content by Barnheater

Yesterday's Tractor Forums
  1. B

    Pulling sled name

    Case Closed!
  2. B

    800 HD manifolds

    I think the original 3 piece exh manifold flows very well as does the intake, they got replaced on irrigation systems because they ran around the clock and cracked as mentioned, but they did flow very well. For pulling they would be just fine but everyone is trying to get as light as possible...
  3. B

    MM G705

    Everything you don't need and then some.
  4. B

    GTB Moline

    Yes you'll need the longer input shaft as well as the longer frame,steering shaft, hood etc.
  5. B

    Chop saw, dumb question

    Hi Grumpy, it might sound stupid but I had some of those wheels that would quit cutting like you said, I was shortening axles on a fella's pulling tractor at the time. I don't know why but it would cut great at first then quit, I found out if I flipped the wheel over (reversed the rotation) then...
  6. B

    G6 clutch

    Dan, I like to run the yoke on as far as possible, this brings the handle closer to ya and should assure enough travel also to camover the throwout bearing.
  7. B

    Royersford Excelsior 21

    Thanks George, they're quite an amazing machine mine still has the original motor on it & its gear driven to the flat belt pulley with a bull gear instead of a belt. I'm not sure of the year of it but I would say 30's or 40's & it works very well. Mine is setup with a Jacobs 18N chuck & was just...
  8. B

    Royersford Excelsior 21

    Thanks.
  9. B

    mm moline u question

    I did it, not too bad. You must swap out the input shaft on the trans for the longer one to reach through the adapter bell. I used all GVI parts, yep it all bolts together.
  10. B

    Royersford Excelsior 21

    Can anyone tell me what size the morse taper is on the quill of a Royersford Excelsior 21" camelback drillpress? Thank You.
  11. B

    MM diesel reputation?

    Thanks.
  12. B

    MM diesel reputation?

    Is it possable to put the 585 heads on the older Lanova engines?
  13. B

    U or G rear ends?

    Or maybe a UMIL that had a high/low gearbox?
  14. B

    G6 clutch

    Hey Captain I like your way, I always use the drive plate like you said but I put it back on the flywheel, I'll try your way the next time should be easier than trying to cog all the teeth and risking breaking one off. Thanx
  15. B

    G6 clutch

    That wont hurt anything Dan, those teeth are probably missing from someone using a jaw puller on it in the past at one time.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top