(800) 853-2651
SHOP NOW

Recent content by Bfinney5238

Yesterday's Tractor Forums
  1. B

    Case 885 Inj Pump ?

    Hey guys I’m trying to figure out the external stop and throttle spring setup as well. Was going to order the springs and setup it up like the factory I was hoping I could get a picture of how it is setup as well.
  2. B

    David brown 885 3pt hydraulics

    Hey do you all know of someone that can rebuild this control valve? or do I need to plan on doing this myself?
  3. B

    David brown 885 3pt hydraulics

    But as for replacing the filter last year I changed the fluid and I cleaned the filter by blowing it out. I couldn’t find the exact replacement. I ordered one but it was smaller. Do you know of the correct filter for it? I’m going to change the fluid again I’d like to change the filter
  4. B

    David brown 885 3pt hydraulics

    well it’s in the past I would explain it but it will take a page worth of writing.. but i figured out the issue. The spool valve on the control valve the one with the double nuts on top for adjustment and the lever on the bottom that pushes it open. Was stuck open I had to tap it with a mallet...
  5. B

    David brown 885 3pt hydraulics

    That’s exactly what it was. But now the 3 pt won’t lift. It worked only on the height selection before this but me trying to figure out what was going on i made it worse. now It won’t lift I can’t get fluid to flow out of the blead port in front of the ram cylinder. I don’t have a hydraulic...
  6. B

    David brown 885 3pt hydraulics

    Guys I’m having an issue with the 3 pt hydraulics not going down. I’ve tried switching the controls on alll three the depth,height and tcu. But it will not drop The lift arms. I’ve been reading my manual but I’ve not came up with possible causes of this problem. I’m hoping you all can. Point me...
  7. B

    Mf 30b power steering pump

    Guys I have a like new power steering pump not even a year old and fluid is leaking around the 3 bolts that hold the pump housing together. The seal is good. Is there a good fix for this? Better crush washers? Hate buying another pump.
  8. B

    Power assist steering question

    Thanks for the replies. Yeah I think Im gonna look for something newer and more nimble to get around in the woods. Im working on a 3600 and it has actual power steering. I didnt realize ford used the same setup on their older stuff like Massey did. I have a case David brown that has a great...
  9. B

    Ford 4400

    Guys I was wanting to know how well the power assist steering works on these tractors? And is it completely rebuildable do the linkages all have bushings that you can replace? One I m looking at is a 8 speed 3 cylinder diesel. How easy are they too maintain? Are they better or worse than say a...
  10. B

    Power assist steering question

    Pretty much all of that. As well as the Massey Ferguson access to the engine. As well as not being able to drop the oil pan without splitting the tractor. And there is a different steering column than the original on the Massey which doesnt bolt up correctly. Is a ford 4400 a better tractor or...
  11. B

    Power assist steering question

    Guys I have a Massey Ferguson 30b industrial that I absolutely hate the power assist steering on. Its comparable to a 165. Im thinking on going to a 68 ford 4400 industrial. Was wondering how finicky the power assist steering is on that tractor compared to Massey Ferguson?
  12. B

    John Deere 350b

    Yeah I think this might have been user error. I did pull a measurement from the dash to the center of the levers. But I had the brake bands too sloppy after reinstalling the final drive. And using a crowbar to hold the throw out bearing just touching the forks I couldnt feel it. I used a screw...
  13. B

    John Deere 350b

    I believe never mind. Think I got it working correctly gonna check it out more tomorrow.
  14. B

    John Deere 350b

    Guys Im hoping to find someone knowledgeable on the 350b. I was getting a grinding noise on my left final drive. When I was pulling it back it would grind. So I though it was worn clutches. Pulled the drive off replaced the clutches and put it all back together. Didnt replace the pressure...
  15. B

    Case 580 transaxle interchangeability

    Guys I found a case 570lxt parts backhoe and Im wondering if I could mate the transaxle under a 580c. Your thoughts.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top