(800) 853-2651
SHOP NOW

Recent content by BGomez

Yesterday's Tractor Forums
  1. B

    Looking for info on this tractor

  2. B

    mm u engine

    What's the HP on that 450 cub motor
  3. B

    4440 PTO Seal Replacement

    Drain the oil pull the pto cover off check the sump screen change the hyd oil filters and remember hyd oil does wear out and needs to be changed after so many hrs of service
  4. B

    2 Cyl 830 PTO clutch

    You will want to remove the drawbar frame to give you more room to work with. Otherwise pretty easy to work on.
  5. B

    Clutch lever bolt

    Call Sunsdahls $58 507-334-8966 the tool works great for the really stub earn ons use a tourch to heat the housing it will push right out
  6. B

    JD Lawnmower Z 737

    Sounds like a short in the pto circuit also check the amp draw on the pto clutch 4-7 amps good 10 and above bad
  7. B

    830 generator

    Did you polarize the generator?
  8. B

    Redneck tire trimming

    Use a cordless belt sander
  9. B

    JD 720 Diesel

    What phone number did you use to call two cyl diesel?
  10. B

    1937 John Deere AO

    Yes
  11. B

    4630 Hydraulic Pump Seal

    You can try just changing the the bleed off/ dust seal and make sure the the bleed off line is open. Otherwise I agree you would have to pull the pump I think you can take it out of the top by removing the deck plates
  12. B

    3010 Hyd- again

    I agree I would check the stroke control valve and also check the sump screen
  13. B

    820 clutch leaking oil

    Remove the clutch clean the oil slinger and use a o-ring pick on the grooves. Also make sure the drain hole is clean and clear.
  14. B

    Grill work on a John Deere B

    I have straightened some pretty nasty looking grills on A's and G's by using Sunsdahls reforming tool set. They have very good top quality tools and they are good people to work with. 507-334-8966 or www.sunsdahltooling.com
  15. B

    How to remove drawbar support bracket from 4020

    Don't forget to check the front drawbar frame pin and bushing if that is loose and sloppy you can wear the load shaft pin even faster. The newer load shaft pins from Deere are softer then the originals.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top