(800) 853-2651
SHOP NOW

Recent content by bigfatricky

Yesterday's Tractor Forums
  1. B

    46A Loader Chatter Shudder

    Hi Folks, Put a 46A loader on my 3010D and I have a question about the return line from the loader control valve. I had asked about the plumbing for this job in a previous post and was handily supplied with pictures from Tx Jim (thanks!), where it was recommended that I go to the rockshaft...
  2. B

    Plumbing 46A Loader on a 3010

    Thanks for the info, that sure is appreciated. One question on the valve: I know it needs to be 2 spool, closed center, no relief, but how many GPM does it need to be? Can anyone give me a link to something appropriate that I can find on the web? thanks again, erik
  3. B

    Plumbing 46A Loader on a 3010

    Hello All, I am going to mount a 46A loader on my 3010. 3010 has single outlet that I would like to keep open. Where is the best spot to tap into to bring power to the control levers and where is the best place to return fluid? Thanks for your ideas.
  4. B

    3010 Loping/prime question.

    Exactly. Fuel was leaking back through it into the crankcase--oil level was way high. Replaced it today along with an oil change. Feeling good about it now.
  5. B

    3010 Steering Line Question

    Found a pinhole in a steering line on my 3010. Can I just put a compression splice on it to repair or should I replace the whole line front to back? I have used compression fittings on automotive brake systems with no trouble, but I don't know how much pressure the steering system develops...
  6. B

    3010 Loping/prime question.

    Howdy folks, My 3010 started loping the other day. Wanted to make sure there wasn't any air in the fuel system so I took out the middle bleed plug. Fuel did not start gushing out of it like I expected it would, but came out after a few manual strokes of the lift pump. Took off the upper...
  7. B

    Water from Ventilator Pipe 3010D

    Talked to a repair feller and he said to not fuss about it, and of course I'm leanin' that way. Just gonna keep an eye on it for now.
  8. B

    Water from Ventilator Pipe 3010D

    Howdy all, Just noticed my 3010D has water coming out of the blowby pipe. Head gasket, right? I used to think it was just some smoke, but maybe it was always steam. Drips water now. Should I finish my pre-winter chores (pull logs outta the woods, rototill, brushhog, light stuff)...
  9. B

    3010 gettin split

    It won't rake gears, bolt is fine on pedal. It won't move at all, no way. I guess I'll find out this week when they tear into it.
  10. B

    3010 gettin split

    I have yet to find out the reason. No resistance in the clutch pedal, it is as if it is stuck in the disengaged position. Park works, all other gears are neutral. Dealer declared the split necessary, though they weren't able to say exactly what was happening. What do you all think?
  11. B

    3010 gettin split

    New clutch going in, anything else to inspect/repair while they're in there? I know about the pto fix b ut don't know if I can explain it to the feller that is doing the work. Is there anything else? I'm sure this has been covered, so I apologize for not searching hard and long. I'm...
  12. B

    3010/3020 Rear Wheel Adjustment

    Howdy All-- Can someone direct me on how change the rear wheel spacing on a 3010? Do I have to have the wheel off the ground to move it? For some reason it seems like it could be quick and easy or a long and painful job. Hoping for q&e...... Thank you in advance.
  13. B

    3010 questions/advice

    Thanks for the replies, folks. I spoke with a couple of dealership mechanics and they both felt like it was just a rusty section getting scrubbed every rotation. The fact that it improved with use made me quit worrying about it. When I started it today, I couldn't even hear the noise from...
  14. B

    3010 questions/advice

    At first I thought the noise was coming from the pto drive gears, which really made me hesitant about the purchase. Are they visible if I take off the 4-bolt plate just behind the inspection plate? Replacement requires a split, correct? Any thoughts about the noise becoming less pronounced...
  15. B

    3010 questions/advice

    Howdy all-- Thinking about buying a 3010D. Everything checks out for me on the tractor but there was one thing that prevented me from handing the guy a down payment today. When I engaged the pto, it was a little noisier than I would have liked. I was having a hard time pinpointing where...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top