(800) 853-2651
SHOP NOW

Recent content by bjhstetson

Yesterday's Tractor Forums
  1. B

    TO 20 RPMs and governor adjustment

    orry, that was supposed to say idle rpms not Ill rpms 🤣
  2. B

    TO 20 RPMs and governor adjustment

    Hello, can someone please tell me what the TO 20 Ill RPMs and maximum RPMs for the engine should be? Also my throttle lever will not stay in the full throttle position I have push the spring on them throttle rod under the breather as tight as I can get it and it still will not stay stable. He...
  3. B

    Ford 3cly LP

    I check out a 2000 3cyl lp today. I can not find where Ford made one. Ford made the 4000 lp 3cyl from 65 to 68.I saw a 3000 lp for sale a few years ago. This was a 65 2000 lp. Have any one on this forum seen one? If it is factory like the 4000 lp 3 cyl, I would think they would be very rare.
  4. Tgrasher

    Chrome moulding

    Anyone have knowledge on where to find the chrome moulding that goes along the fuel tank on a 630 - part # G46259 and I think it's the same on a 530?
  5. B

    To 20 12 volt conversion.

    I found the 12 volt kit for the generator, do you remember what voltage regulator you used? Does the wiring stay the same except changin from positive ground to negative ground?
  6. B

    To 20 12 volt conversion.

  7. B

    TO20 Oil leak

    Turned out that they gave me a filter that was a bit long, Got the right filter from Tractor supply. Used a good amount of gasket sealer since I can not get seal local. will have to be ordered, Solved problem. Thanks for the help.
  8. B

    TO20 Oil leak

    Turned out that they gave me a filter that was a bit long, Got the right filter from Tractor supply. Used a good amount of gasket sealer since I can not get seal local. will have to be ordered, Solved problem. Thanks for the help.
  9. B

    To 20 oil leak at distributor

    Turned out that they gave me a filter that was a bit long, Got the right filter from Tractor supply. Used a good amount of gasket sealer since I can not get seal local. will have to be ordered, Solved problem. Thanks for the help.
  10. B

    To 20 12 volt conversion.

    Good moring, I am trying to convert over to 12 volts. I have the block with the un-threaded TO30 bosses on it. the bracket will not bolt up due to bracket mount ear has a squared off spot cast into it. The other TO20 block has a rounded off ear at the bracket location.Does anyone have any...
  11. B

    TO20 Oil leak

    Any tips on how to stop oil leak at filter cover after changing oil? Thanks for your knowledge
  12. B

    To 20 oil leak at distributor

    Thanks for your advice, How do I stop the oil filter plate on the pan from leaking oil after I changed the oil? Thanks in advance for your knowledge
  13. B

    To 20 oil leak at distributor

    the oil level is good, does not seem to have gas in it, the tractor has been sitting for several years.
  14. B

    To 20 oil leak at distributor

    I can not tell if the vent tube is working. I can not feel in air from the tube
  15. B

    To 20 oil leak at distributor

    I was given a TO20 By my wifes uncle, serial # is 103430, I believe that is a 1948 model. OIl is leaking at distrbutor when engine is running, I pulled valve cover to check vent tube, carb cleaner ran throught it fine. Any advice?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top