Recent content by Bob-O

  1. B

    PTO qiut

    Thanks again. About 8 yrs ago when I purchased this tractor there were a few things that needed tweeked and you guided me through them. Nice to have an intelligent man like you sharing your knowledge for so long. I was delighted when you responded even tho I'm pretty sure you nailed it and that...
  2. B

    PTO qiut

    Thanks for the reply Majorman. What is involved to repair that? Will it require a split?
  3. B

    PTO quit

    Could'nt edit but forgot, is there any kind of shear pin it could be. If so how/where do I fix it?
  4. B

    PTO qiut

    I have a fordson super major and was mowing tall, thick Thisles the other day and after boout 3 trips around the small field I noticed it quit cutting. The PTO and three poing just stopped working. No big clunks or smoking, pto just stopped working. The bush hog will spin freely when...
  5. B

    64FSM

    Bendee, the neighbor had to order an owners manual, the problem was it came out of time (the injector pump.
  6. B

    64FSM

    I just now took it over to him and I don't know when he'll get to it. I will post results, good or bad.
  7. B

    64FSM

    Just read Barret Scotlands post and I believe I put a can over the block breather like he said he had, would this make it get too much fuel/not enough air and if so, what to do?
  8. B

    64FSM

    Hello, I have a FSM that started within 2 seconds when I bought it several yrs ago, now it won"t start without a shot of either (I know). I only ran it about two hrs all of last summer, would"nt start this yr till I gave it a shot. If it were an old v-8 I"d describe it as only...
  9. B

    Dearborn loader

    Thanks Brian and congrats on yer new (to you) 27
  10. B

    Dearborn loader

    DD, thanks for the reply. Won't the pump work off of the aux hoses locsted under the seat? If not , what parts are needed to atatch to the front pulley and isn't that behind the grill and radiator/ Will this be too much hassle to mess with rather than try to keep searching for one that just...
  11. B

    Dearborn loader

    i have a 63 FSM and have been trying to find a loader for it for some time. My son in law calls and says he's found one that will fit. It is a deerborn model 19-71. The guy selling it says it will fit right on, something about it mounting to the rear axel (does that make any sense)? My...
  12. B

    Hitch types

    I know there are different classes of hitches. I have a Fordson super major. I came across an old FORD SINGLE PLOW AND BOUGHT IT. NOW, THE PROBLEM IS THE BARS-PINS ON THE PLOW ARE WAY TOO NARROW AND DON'T PROTRUDE FAR ENOUGH TO GET FAR ENOUGH THROUGH THE BALLS ON THE 3 POINT ON THE FSM. (SORRY...
  13. B

    63 FSM clutch

    Am I incorrect by believing that if the clutch does NOT disengage that the tractor needs split and if going that far should the pressure plate and throwout and pilot bearings(dual clutch) be replaced? Also resurface the flywheel Ballpark guess on parts and labor please. Thanks in advance, Bob-O
  14. B

    FSM clutch oil pump

    I recently had my 63 FSM clutch and oil pump replaced. They also had to reset the injector timing, replace one rod bearing and polish the crank. The parts were $385, misc was $66 and labor was $2084. I am going to go discuss (negotiate) this bill. I am not a great mechanic but think at $62 per...
  15. B

    FSM fuel system

    I took the fuel sediment bowl and fuel filter off my FSM. Am getting a new filter , brass screen and gasket for the sediment bowl tomorrow. After I reassemble these things, how do I go about bleeding the lines? Do I just disconnect the lines where they enter the head and crank until fuel spurts...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top