(800) 853-2651
SHOP NOW

Recent content by Bob21 Martin

Yesterday's Tractor Forums
  1. B

    350 high utility wheel bearings

    Thanks D Slater. Looks like that's going to be a project before hay season comes around. That's my raking mule. Bob
  2. B

    350 high utility wheel bearings

    All righty. That's what I needed to know, Jim Thanks, Bob
  3. B

    350 high utility wheel bearings

    ?Are these replaced by taking the hydraulic reservoir off or can you get to them through the back PTO Thanks for the help, Bob
  4. B

    IHC 350 utility hydraulics

    Well, I got that thing taken apart, cleaned it up and stuck it back together. There wasn't anything that stood out in the regulator as a problem - no dirt or sludge and it really looked good as far as wear. The lift did work better though/ But I let it run a little and the engine loading...
  5. B

    IHC 350 utility hydraulics

    OK. Thanks a lot Jim. I'll take that regulator apart tomorrow and I understand the spring will take some care. I've had this thing for forty years and not much trouble. I've got chains on it for this winter in Iowa and I can push snow better with it than I can with my 806 and no chains. I...
  6. B

    IHC 350 utility hydraulics

    I'll get the diagram in front of me with the tractor and see if I can take that thing apart. Thanks again, Bob
  7. B

    IHC 350 utility hydraulics

    Thanks Jim. The pump that I see is on the right side of the engine just below and to the front of the distributor. Then two lines go back to the reservoir under the seat. There is a block under the main control spools with lines back to the cylinder on the hitch. I have taken the...
  8. B

    IHC 350 utility hydraulics

    I have a problem with my IHC 350 utility hydraulics on the fast hitch. From information I have gotten here and appreciate greatly, I know my tractor has a check valve in the valve bank to prevent the hitch from lowering. It has just recently started lifting and lowering very slowly. I...
  9. B

    350 utility valve control setting

    Thanks D Slater: I would have to go to a two way cylinder on the mower lift to use a check valve, then. The one way cylinder came on the mower and I've just kept it. A cylinder that small isn't expensive. I may go ahead and change it over to a double and be done with it. Most of the field...
  10. B

    350 utility valve control setting

    Thanks Mark. Years ago, I had mentioned at IH Parts I couldn't keep the cylinder up on the mower and the parts guy said "just put a check valve in the line" What I couldn't understand was how to release the check in the line when I wanted the mower lowered.
  11. B

    350 utility valve control setting

    I see. Mine has the two lines and the pin hole you mention. I use that hole on a lowboy with a light tongue when haying. It comes in handy. The hitch works really well. When I have the one way on the mower is there a check valve to put in that line or do they only work with two ways...
  12. B

    350 utility valve control setting

    Thanks Mark: I've had this thing for twenty eight years and always had trouble with the mower, which is a one way cylinder. I use one of the loader lines for the bucket on it. Never once did I think about turning those valve knobs (don't know what they are actually called). When I got all...
  13. B

    350 utility valve control setting

    Thanks a bunch for the information D Slater. I take a look and get that set up. The two one ways I have are the loader lift and the mower. The lift has always worked well, but the mower has always been a problem. Maybe this will take care of it. Thanks again for the help, Bob
  14. B

    350 utility valve control setting

    On my 350 Utility I have two valve blocks with levers for the loader lift and one for the bucket. Then towards the rear I have one for the two point. On each of the blocks there is a short end of a shaft, flat on two sides, that sticks out about half an inch from the casing on each. On the...
  15. B

    806 Hydraulics

    I think it's a WIX filter creation.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top