(800) 853-2651
SHOP NOW

Recent content by bobthetoolguy

Yesterday's Tractor Forums
  1. B

    9N Conversion Questions

    I found the rectangular resistor was broken fellas. I'm going to replace that and see if she fires up. Thanks for all of your help!
  2. B

    9N Conversion Questions

    I have a "40 model 9N that has had a long time 12V conversion. She didn"t answer the call this spring and while doing some backtracking, I cannot find rhyme nor reason for some of the wiring. I have "borrowed" several of the schematics on here and found them to make sense. My question is: If...
  3. B

    Barn Fire

    Thanks bc. We're on it. My insurance company says I'm covered... for what that's worth. Losing the M and my Case SC really hurt, but Ive got another M and another SC. What really stinks is losing the 1937 Case RC. It was a single tire front end and a really neat little machine. I haven't...
  4. B

    Barn Fire

    Thanks for all of the input and support guys! My insurance agent says that I"m covered for whatever that"s worth. I know they got pretty hot since the aluminum melts at about 1100 degrees F. The funniest thing is the radiators. Both radiators are still in tact with water inside. Thanks again...
  5. B

    Barn Fire

    The link I added on my previous post went untitled. For those interested, here is a link to the newspaper story from today's paper. Brush fire destroys barn
  6. B

    Barn Fire

    Fellas, I need some help! Yesterday, the barn containing my 1953 Farmall M (along with two of my Case tractor restorations) burned to the ground. As you might expect, she got pretty hot. This is a fine tractor with power steering, live hydraulics and the M&W hand clutch. Is there any hope of...
  7. B

    Barn Fire

    Fellas, I need some help! The barn containing my 1937 RC and my 1953 SC (both fully restored and ready to work or parade) burned to the ground yesterday. I live three hours away, so I didn't get to look at things myself, but from the photos my friend took, it looks like the ol' girls got...
  8. B

    9N Hydraulic Questions

    Thanks so much guys for all of your help!
  9. B

    9N Hydraulic Questions

    Hi Fellas, I need some help from you experts out there. I recently installed a Freeman Loader to my 1940 9N. I am using the 1/2"-20 Plugged hole that the IT manual calls the pressure test port to run the loader. I made a neat "banjo" fitting and included a hydraulic gauge in the circuit so I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top