(800) 853-2651
SHOP NOW

Recent content by BossBrown

Yesterday's Tractor Forums
  1. B

    Pulling tire size

    Well, I tried posting a message yesterday evidently didn't work. I have a 1950 John Deere G it has 13.6 x 38 tires (Firestone) on it now. I pull in the 6,000 & 7,ooo classes and do ok. The tractors (different brands) that do consistently better seem to always have bigger tires i.e. 15.5 x 38...
  2. B

    Switching front pedestal

    I have a junk JD G I want to take off the front pedestal it has the roller flex front and put it on my 1945 JD A. I have measured them up and they seem to be the same. Can these be swapped out and work? Thanks
  3. B

    Rock Shaft

    First, let me thank all of you for your replies. The rock shaft arms are original John Deere as stamped on them and it's obivious that they are antique. I've finally measued (as I should have done to begin with) and the shafts are and inch and three eighths as are the rock shaft holes. By eye...
  4. B

    Rock Shaft

    Evidently I haven't made myself too clear on what I'm trying to do, not unusual for me, don't get old! Anyway, simply put I just can't get the rock arms to fit on the rock shaft on my late styled John Deere A. The square holes are just way too small on the rock arms to fit on the rock shafts...
  5. B

    Rock Shaft

    The old saying, "size six hat to fit on a size ten head" not even close.
  6. B

    Rock Shaft

    I recently purchased the rock shift arms (P831 & P832) to put on the late styled power trol rock shaft arms to eventually put an 800 three point lift. I sized them up to the rock shaft, if there is a way to put them on it's beyond me. The shaft is quite a bit larger than the shaft holes...
  7. B

    Roll-O-Matic (G)

    I'm located in Northern New England. Thanks
  8. B

    Roll-O-Matic (G)

    It does have a convertable extension, I believe I can switch them right over there are only four bolts. Thanks again
  9. B

    Roll-O-Matic (G)

    Unfortunetly, I believe it is a single piece pedestal, don't get old I'm going to have to go out and look. Thanks
  10. B

    Roll-O-Matic (G)

    I have a 1950 JD-G with Roll-O-Matic front end. I'm looking to change it to a straight front, where I live it's hard to come by JD parts. There is a JD-A with a straight front for sale, is it a possibility that will fit? Thanks
  11. B

    John Deere G Oil Bath

    I have a 1950 John Deere G, I want to take the oil Bath out do I have to take off the cowling to do so? I have a John Deere B and with that I have to take off just about everything to get at anything. Thanks
  12. B

    Haverhill NH pull

    It does sound confusing, but I agree there are some drawbars set up like yours. I don't see the problem with the way you have yours set up it's probably as strong and safe as any. North Haverhill has strange weight classes I just don't go anymore I have to bring an extra 1,000 pounds of...
  13. B

    Replacement bearing

    I need a bearing (JD 7684) which goes into a JD-G 1950 in the steering pedestal. Went to my JD dealer it came up obsolete, to their credit they looked in several place with no luck. Would much appreciate any info where I might get one. Thanks
  14. B

    JD-G steering problem

    Thanks, my neighbor has a good loader, haying season has started will be a while. Thanks again...
  15. B

    JD-G steering problem

    Appreciate the reply. The whole assembly has to come off in order to get at the that washer and possibly the bearings? I've taken those apart before all the top tin work and the front pedestal have all got to come off? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top