(800) 853-2651
SHOP NOW

Recent content by Brady Miller

Yesterday's Tractor Forums
  1. B

    Char lynn power steering o rings

    I posted before that I didn't think that was correct on the sk122 kit. Well I stand corrected. I ordered 2 kits last time and didn't use because they were bigger than the shaft, but not after installed in the housing. I stand corrected. Thanks to all that help
  2. B

    Char lynn power steering o rings

    Ok guys, Just to get this straight in my head, I need square o rings and they will last. I did this before, got the kit ordered with square rings and they were too big so I used some close o rings I had and here I am doing it again. Does anyone have a part number?
  3. B

    Char lynn power steering o rings

    Where do I get them bob?
  4. B

    Char lynn power steering o rings

    Gents, Need to replace the o rings in my char Lynn torque genny. Any info on the size would be great. Here"s a pic of the torque genny.
  5. B

    International Seal conversion website

    Gents, I have found a handy tool. The link below is a site that will change over international seal part numbers to SKF seals popular at your local Napa. http://www2.chicago-rawhide.com/popup_parts_lookup_457012.htm I hope this helps. It sure helped me. In the big cities, no body carries...
  6. B

    Farmall h 6 volt

    Thanks gents. I thought I could just double checking.
  7. B

    Farmall h 6 volt

    Gents, Help me out here. I have an h with positive ground 6 volt and generator and mag. Can't I replace the battery, starter, and genny, with 12 volt and do nothing to the mag? Thanks
  8. B

    SMTA hydraulic setup

    Gents, I am reconfiguring my SMTA with a 2 spool 2 position hydraulic valve system. The factory setting on the bypass is set at 2000 psi. What is a good rule of thumb to set the pressure at for my SMTA with a live hydraulic pump? I have a Farmall M and I put a live hydraulic pump and a...
  9. B

    Farmall m trouble

    I don"t have the cover off yet, but the I have listed the compression test
  10. B

    Farmall m trouble

    Rotor is working and correct
  11. B

    Farmall m trouble

    Gents, I was pulling a land lever with my m, I beared down on the hydraulics and hit the end of the hydraulic stroke, the motor snuffed out. When I tried to restart, it just turned over. Thought it was electrical, replaced all electrical points rotor cap condenser coil. No start Got the...
  12. B

    1961 gmc 1 ton

    Thanks john
  13. B

    1961 gmc 1 ton

    I have a 351 v-6 and a 5 speed manual tranny. I would like to gain some road speed. What kind of tranny do I have, shift pattern below? Is a 2 speed rear end possible? If so where"s a good place to start looking? I"m not sure of my rear end ratio either.
  14. B

    Farmall h weak spark

    Jim, No I do not have that picture. can you send me one?
  15. B

    Farmall h weak spark

    Is the magnet the cylindrical piece going through the coil or the sides where the coil screws to? I haven't worked on mags much. If someone could briefly explain or point me to a video or something on how the mag works. Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top