(800) 853-2651
SHOP NOW

Recent content by Brandon1107

Yesterday's Tractor Forums
  1. L

    the pond is full again

    It rained pretty good last week ., so the pond in pa is full again It was very low most of the summer, I took some pictures of it sunday morning, That is turnips growing in the garden,
  2. E

    MF 65 sheet metal

    I"m putting a MF 65 with a Continental gas engine back together and can"t figure out where the heat shield that goes over the manifold bolts to. It looks like the front uses the same bolt as the gas tank, but where does it bolt to in the rear?
  3. P

    4020 Serial Help

    Hello I've just found a 4020 PS, in rather poor condition and the serial on the rear axle is: SNT223P114469R I work out its a '65 - is there any other info hidden in there?
  4. E

    cutter bar for #31 MF Dynabalance

    Still looking for Cutter Bar for Model 31 MF mower. Don't need sickle bar, looking for the bar the guards are mounted on. It mounts to the mower by three bolts in a triangular pattern that screw in to threaded holes in the bar itself. Any body know where I can find one? Would take a whole parts...
  5. F

    730d

    can anybody in the south east build a STOCK APPEARING 730d ???
  6. A

    Strange issue??

    In the last two weeks my 9N has done this twice. It died at lower engine speed so I figured I must must have done it. First time it fired up right away and I noticed the charge gauge pegged to the right. Then it went back to normal after about 30 seconds. Today it died but would not refire. I...
  7. M

    MASTER PART INDEX

    I keep seeing reprints of the Deere Master Part Index on ePay and they are always listed as material that is in the public domain. Anybody know what part of the public domain it is in? I would like to download a copy without paying somebody on ePay to do it for me. I have looked at every...
  8. R

    Mustang skid steer

    I just purchased this skid steer with a Z 790 Hatz diesel to put in it. But I do not know the directionof pump rotation. If you are standing at the back of machine looking forward. What is the direction of pump rotation? CW or CCW. Also I have the option of putting a Wisconsin VE4 in it...
  9. B

    1970 Ford 2000 Generator question

    Soundguy, I put the voltage meter on the battery leads with the battery disconnected. I did the jumper trick and no change. The gen did motor so I bypassed the reg. and it started charging. On my way to get a voltage regulator. Thanks A Lot for your very helpful post. Brandon
  10. B

    1970 Ford 2000 Generator question

    I have a ford 2000 Diesel and I do not have the gen light working yet. When I put the volt meter on the battery leads I get 0.2-0.7 volts depending on RPM"s. What should I look for coming from the Gen in volts for it to be good? Thanks, Brandon
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top