(800) 853-2651
SHOP NOW

Recent content by Brian Stortenbecker

Yesterday's Tractor Forums
  1. B

    Things You Do Not Want To Find On Your Tractor!

    Spray the head gaskets with copper coat, this stuff is awesome, if it leaks with that, the block will need decked.
  2. B

    Marty in Bad Ax Mi. what is a phone #

    I have had good luck with Marty. Bought a lot of parts off eBay for I think was some pretty good deals. In fact I just got parts today from him. Never dealt with him n person.
  3. B

    ta replacement without splitting?

    I thought I was the only one with a magic wand. Haha
  4. B

    4650 water pump

    Neighbor needs a water pump in his 4650. Hycapacity shows 2 water pumps. The only difference I see is one has a weep hole. It also tells me to make sure the gear numbers match between the old and new pumps. What's involved in putting a pump on. Any tips also appreciated. I'm a red mechanic very...
  5. B

    4490 ticking, from rear rear of engine under load

    I would also say exhaust leak, have a friend that's an awesome case mechanic. He told me to double up exhaust gaskets. Before you take the manifold off use a marker and mark the ends to the middle section, then take it to get cut to make sure it's straight.
  6. B

    1486 center section removal?

    I roll away the engine, I had stands built to roll the center section out. Works awesome.
  7. B

    806 starting

    White smoke at initial startup can mean a cold cylinder but should go away after a bit of running. Also an injector tube could be leaking coolant. A good way to know if the valves are at fault, the warmer it gets outside the easier it should start. If you start it and let it run for just a few...
  8. B

    806 starting

    Good possibility that the valves are sunk in the head. 361 and 407 are know, when the valves are sunk they start hard. If you have the head done plane it and do a complete valve job with new hardware. Use the min. Spec when doing the head. It also could be pump and injectors.
  9. B

    Pitting in o-ring groove in JD 6-404 engine block - Options

    I would not do anything but have it bored and put new counterbores in. You must use a machine shop that has experience with this. I had a case block done, he did the lower and uppers done. I would also have the block decked, he will need a new sleeve to recut the counter bores to get the right...
  10. B

    7110 magnum trams problem

    Cold weather can cause a lot of weird things. If it were me and it started all of the sudden, I would either get it in a warm shop or wait till it warms up. Or get it on a Dyno to warm the trans fluid up and then try.
  11. B

    7110 magnum trams problem

    High range is 13 thru 18, so I assume if low and medium do not work, it may be in the control valve. Did this happen all of the sudden?
  12. B

    7110 magnum trams problem

    What gears do you have, the range trans consists of low, med and high clutch packs.
  13. B

    Running Case 2290 Hydraulic Remote in Constant?

    My dad ran a 2594 for years with no trouble, he just flattened a piece of heater hose and stuck it in the slot.
  14. B

    5288 low range

    Maybe a bit of confusion. I'm talking low range, which should be behind the master clutch, the speed trans works great.
  15. B

    5288 low range

    Should say the speed trans works great.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top