(800) 853-2651
SHOP NOW

Recent content by Brianjbell

Yesterday's Tractor Forums
  1. B

    Allis B hydraulic pump question

    Hi all, new to the Allis B. My hydraulic pump is missing the roll pin for the plate to shaft connection. Can someone tell me the dimensions so I can procure a new one? Thanks in advance!
  2. B

    1936 unstyled B newbie question

    I'm hoping this is in fact what's going on. I'm still looking for my laser thermometer to actually test. The gauge looks to be the factory one, or a very old NOS replacement from ages ago.
  3. B

    1936 unstyled B newbie question

    Level hasn't budged, don't think it's the head, no other issues of cracked head. Will keep an eye on it though. Also going to test to see what the actual concentration is.
  4. B

    1936 unstyled B newbie question

    All, long time lurker, first time owner. Just got a 1936 JD Unstyled B, it's sat for a while but in overall good condition. I've noticed that it seems to get very warm when running (and it's in the high 30s-low 40s here in NC at the moment). The temp gauge reads between 190-220 on it. The...
  5. B

    JD 4052m no crank

    Problem has been resolved. The solenoid wire is a spade connector and had vibrated back enough to look connected but was not making connection. After reconnecting we are back to normal.
  6. B

    JD 4052m no crank

    Sorry I didn't address this in previous post. This has been done as well. Also checked voltage from battery to the starter, including all fuses. All is good there too. I'm thinking either some safety switch is out of whack or the solenoid on the starter is dead. I've already got a call into...
  7. B

    JD 4052m no crank

    This unit is a hydro. I've tried with range selector in all ranges including neutral with no success. I did confirm (and cycled to be sure) that PTO was off. When I turn the switch to the start position you can hear the relay under the dash clicking each time I try to start, just not getting...
  8. B

    JD 4052m no crank

    No, I'm in NC and mud is about as close to snow as we have here right now. None in the area that I was working in yesterday. I've tried everything I can think of related to pedals/switches and no dice.
  9. B

    JD 4052m no crank

    All, I have a 4052M with less than 100 hrs. Started it this morning just fine, ran for an hour or so with no issues. Shut down to talk to the JD tech that was here to do a recall on my Z730m. I got back on the machine to start it again and it has no start. The dash lights up, beeps like...
  10. B

    Long 310 missing past half throttle

    All, Long 310 had blown head gasket. Replaced it along with surfacing head. Starts, idles and runs well until you go past half throttle. Starts stumbling/popping bad. Pump was rebuilt not long ago. Valve lash set at .015. Any ideas? Not much info to be found on these old girls.
  11. B

    blown head gasket on 9N?

    Oil in antifreeze is another symptom
  12. B

    K301 straight pipe

    All, I have a K301 on a CC 124 that I'm building as a puller for my boys. I'm looking to install a straight pipe on it and noticed that it doesn't have the bolt holes drilled and tapped for the MidWest SC flange for straight pipe installation. Wondering if anyone else has come across this and...
  13. B

    Waiting and waiting ....

    Ordered sleeve service tools from TOH in December. Thanks to USPS, tractor is still down: December 28, 2020 In Transit, Arriving Late Your package will arrive later than expected, but is still on its way. It is currently in transit to the next facility. December 24, 2020, 11:09 pm Departed...
  14. B

    Almost ready for prime time

    As usual TOH, your work is amazing! Can't wait for the USPS to deliver the tools you made for me. Sad 8N block still hanging upside down waiting for a heart transplant. Bet all its blood has rushed to its head by now.
  15. B

    The little pin

    It's amazing what that little bit of material can do for you. The first 8N I had was worn half way thru. Went from barely pickup up disk harrow to over a foot of ground clearance.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top