(800) 853-2651
SHOP NOW

Recent content by Bruce Reimer

Yesterday's Tractor Forums
  1. B

    No luck today with the 1755

    I don't know that the reg. has a lot do with starting, this has to do with charging the batt. Do you have a safety switch on the clutch pedal that needs to be pressed in for starting?
  2. B

    Bosch P7100 pump governor

    Can anyone tell me what the governor # is on the P7100 pump with an AG governor? Should be RSV type. I need the number off the back of the pump, governor end. My pump is on a 5.9 engine and it needs an AG governor. Thanks. Bruce
  3. B

    Massey ferguson 1100 Fuel system Problem

    The Perkins hate air, they are real fussy. The pump has 2 small bleeder screws, after pumping them clear you will most likely have to crack an injector or 2 to get it going. Also seems to help to open the throttle quite far for cranking. Can't tow a M.P. trans. to start. Good luck Bruce
  4. B

    pics of finnished repower on 2-150

    I forgot one important thing. Let me say a big THANK-YOU to all of you who have helped in this project. Some I have talked to by phone or in person and some just by reading of your experience on your posts. This is a very helpful forum. Thanks again. Bruce P.S. you may find my choice of...
  5. B

    pics of finnished repower on 2-150

    I took the 2-150 out for the first time today and noticed the steering is wondering quite a bit. I have the front end off a 2-155 and put new seals into the steering unit, tie rods are all good, wheel alignment is good. With the old 2-150 setup it handled real nice. Is this a problem that is...
  6. B

    OC3 IXB motor info

    I'm with Chuck, I hope you used some kind of "sticky" lube on the shells when you put them in, "Bearing Guard" is what I have used. You will be amazed how much easier the engine turns once the oil pressure is built up. Good luck Bruce
  7. B

    tractor

    Hi Jeff, I wish mine did turn 540 at 2000 RPM. The Super 90 I have and the 35 I had both have STD. PTO speed at just under 1600 engine RPM. The tractor would be much more useful if it ran at the proper engine speed for the std. PTO. I have never got a good answer as to why the boys at MF thought...
  8. B

    2-155 White

    Does someone know what color the meshed grate is supposed to be that is in the lower front sidepanel on the 2-155? Thanks, Bruce
  9. B

    Allan In NE twin new holland rakes

    Allen, Could you send me a pic or 2 of how your hitch is set up for the 2 rakes. Thanks Bruce
  10. B

    5.9 Cummins problem

    Thanks guys, If I pinched the return line with a pliers it ran fine. I took the banjo bolt valve out and for some odd reason the spring was cocked to the side and the ball was loose. Put it back in the way it should be and it was nice and tight. I don't know why something like that would happen...
  11. B

    looking for water inlet elbow for 5.9 Cummins

    I need to find an elbow that points forward for the 5.9 C, bottom right hand, uses 3 bolts to attach. Part # is 3934876. I would like to find a used one, Cummins wants an arm, leg, and about 3 quarts of blood for this thing up here in Canada. Mine points down at close to 80 degrees and my rad...
  12. B

    5.9 Cummins problem

    Thanks guys, I think I found the problem, if I restrict the return line with a pliers the engine runs fine. The valve inside the banjo bolt on the return line from the inj pump was not seating. Thanks for the help Bruce
  13. B

    5.9 Cummins problem

    I have a problem with the 5.9 that I put into my White tractor. It came out of a bus, has the P7100 pump. The first time I ran it I could run it at idle but as soon as I tried to rev it past about 1200 RPM it would run the pits and smoke like on a -40 day. I left it for a few days and the next...
  14. B

    5.9 Cummins problem

    I am putting a 5.9 into my White tractor. Got an engine from a bus with the P 7100 pump. The first time I ran it I could run it at idle but as soon as it went over about 1200 RPM it would run the pitts and smoke like it was -40. I left it sit for a few days and the next time I tried it it worked...
  15. B

    MF 1135

    They were a good machine in the day, If it has been used for a lot of heavy work you will need to tend to the final drives. They can be switched left to right if done in time. I know this because I had one with this problem. The latter ones had a slightly heavier gear set (silver wheels). I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top