(800) 853-2651
SHOP NOW

Recent content by bschulte

Yesterday's Tractor Forums
  1. B

    Kubota M4030SU

    Hello, I have a recently purchased Kubota M4030SU with the 5 cylinder engine that hadn't been started in a while. The engine fired up but immediately ran past wide open. I luckily got it shut down before damage occurred by pulling the fuel line apart and it finally died. I found that the fuel...
  2. B

    Ford Funk 6 cylinder

    How much and where are you located?
  3. B

    Ford Funk 6 cylinder

    Hello, I currently have a locked up 226 flathead inline 6 cylinder ford funk engine in my 8n ford. I bought it that way. I'm curious if anyone would know if I could swap in a 223 cu in 6 cylinder overhead valve engine. Records show they did a 215 cu inch 6 cylinder funk conversion in a...
  4. B

    Ford Dual Remote Valve Assy.

    Thanks for the info! I visited my new holland dealer and parts are available.
  5. B

    Ford Dual Remote Valve Assy.

    Would someone know what's behind the slotted bolt shown in the attached photo of my dual remote valve on my Ford 4600? It leaks from the screw. Does it just need and o-ring? Can I just unscrew it from the housing?
  6. B

    Cylinder Heads

    Thanks for the advise. I'll stay with what I have. Can you or anyone recommend someone who builds a pulling cam that will work with my 414 cubic G engine? I'm guessing I run about 30% or so over factory rpm.
  7. B

    Cylinder Heads

    I currently have 4210 cylinder heads on a basically stock MM G pulling motor except that is bored .060. I have found some 4206 heads that I can put on it. Would anyone know if that would make much difference in hp. Run ok? Thanks! Different cam instead for more hp gain?
  8. B

    Case DC Pistons

    That sounds interesting. I'll check into that as well. Thanks!
  9. B

    Case DC Pistons

    It looks like Doug has used some 4 3/8" pistons from a bigger case tractor. He will likely be able to help. The john deere pistons from a 3020 are way more affordable. Has anyone tried them in the past and how much hp did it produce? I will try to contact Doug in the near future also. Thanks!
  10. B

    Case DC Pistons

    Thanks for the info. Tom certainly posted his fair share of informative replies on many various topics. I'm betting he is greatly missed by certain people. I do hope to find some other ideas from anyone who actually used either the 4.25 or slightly bigger pistons. Thanks again!
  11. B

    Case DC Pistons

    I currently pull a Case DC with 4" pistons in 4500 and 5500 pound classes. I'm placing and winning occasionally but would like more power for next year. I wanted to know if someone might have some good used 4.25 or 4 3/8" pistons they might want to part with. If not does the John Deere 3020 gas...
  12. B

    DC Carb.

    I have a Case DC that I'm looking to pull at some point. It has a defective carb that needs cleaning and a kit at the least. I was wondering if a different bolt on carb might be more effective. Any other options. It currently has a Zenith and the model badge is missing from the carb. Thanks in...
  13. B

    Case DC

    What sleeve and piston combo did you use for the 4 3/8 combination?
  14. B

    Case DC

    1950 DC case with hand clutch, gas manifold, and 5505 head. Would it have standard bore unless someone overhauled it in the past? Is it possible to check the size of the piston through the inspection plate on the side of the block? What kind of oversize sleeve and bore is most commonly...
  15. B

    Case DC

    Just purchased a Case DC. Looking to make a pulling tractor out of it. Wanted something not seen much in the area. Has a 5505 gas head on it. Will it have good power increase if it's port and polished, different valves, or do I need to look for a 5576 head? Looking for descent increase in...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top