-
B
Electronic Plug Wire Recommendations
Thank you all! I replaced my wires with the NAPA and swapped my Autolite Plugs for the NKG and she is running great. Did not realize how long it had been since she was tuned up. The plugs were sooty and a couple were oily. Don't know if that was the issue or a symptom of the issue, but for now... -
B
Electronic Plug Wire Recommendations
I really appreciate the info. I will do all of what is suggested! Electrical issues are my hamstring. I can turn a wrench, but electrical issues really tie me in knots. -
B
Electronic Plug Wire Recommendations
Forgot to mention two things, issue happens on different coils, and the arcing is from coil boot to coil body. Changed coil wire and temporarily helped, but went back to terrible arch. -
B
Electronic Plug Wire Recommendations
I have a recurring problem with my EI 841. After rebuild many years ago, it ran great for years, then began coil arcing. Replaced plugs, coil, cap, rotor, and wires. Ran great for a few months, then arcing. Replaced everything ect. Problem keeps reoccurring. My question is........should I... -
B
Clutch still stuck.
Is there anyway to unstick a clutch through the starter cavity? I've tried driving around and no luck. Really don't want to split the tractor so any ideas are appreciated. Tractor is a 19571sh 600. -
B
Clutch still stuck.
Is there anyway to unstick a clutch through the starter cavity? I've tried driving around and no luck. Really don't want to split the tractor so any ideas are appreciated. Tractor is a 19571sh 600. -
B
Stuck Clutch
Ford 600 Clutch is stuck again. The first time, I got it unstuck by just shoving it in gear and driving awhile. Came unstuck and worked fine. Now the clutch is stuck again and will not release. Please advise. Thanks -
B
Z-134 Timing
thanks great info. My tach is for autos with a six or eight cylinder. I just use the eight and figure it out.- bwilso
- Post #7
- Forum: Massey-Harris & Massey Ferguson
-
B
Z-134 Timing
That's my question. I cannot get 600 RPM's therefore I need to ck it at higher RPM's. What degree should correspond to what RPM in a higher range?- bwilso
- Post #3
- Forum: Massey-Harris & Massey Ferguson
-
B
Z-134 Timing
About to finish putting my MF35 back together and have a timing question. Manual shows setting timing at 600 RPM's. I cannot get my tractor to run at such a low RPM. What do you guys set timing at? Tractor is gasoline engine. Thanks Bob- bwilso
- Thread
- Replies: 6
- Forum: Massey-Harris & Massey Ferguson
-
B
Electronic Ignition Spark Question?
Andy, just realized I have posted on wrong forum. I have three Fords so I normally used this forum. This tractor is a MF35 with 134 engine and does not have rotor clip. Very similar to my fords just distributor is on opposite sides of engine. -
B
Electronic Ignition Spark Question?
Tractor will run with old distibutor and using points but very weak spark. Tractor has run very well for years using EI. Tractor started running poorly, then not at all with EI. Replaced EI Module, along with distibutor, cap, rotor, wires, plugs. Compression is good on all cylinders. thanks -
B
Electronic Ignition Spark Question?
The coil to ground spark is jumping 1/2" but almost non-existint spark at plugs. Replace EI module and same issue. What could possible be the problem? I have new rotor and cap.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy