(800) 853-2651
SHOP NOW

Recent content by Case-O-Man

Yesterday's Tractor Forums
  1. C

    511b Venturi

    I'm having trouble locating a replacement venturi for dads 511b. The venturi has a chunk missing from the choke side lip. Marvel Schebler TSX-749 carb. Case venturi part number is 46-438, 7/8" inside diameter at narrowest point and 1 7/16" throttle bore. Part has been discontinued and I have not...
  2. C

    any you CASE guys ride motorcycles

    I know what your going through I ride a 1986 Yamaha virago 700 and a Yamaha XT 350. I have only had the dirt bike out once this year and have not even looked at the virago. It's going to be a long summer if it stays like this.
  3. C

    roll call for all Case people here

    Austin Moser, Elkader (north east) Iowa I recently bought an 830 comfort king case-o-matic diesel after my great grandpa and my grandpa passed away this summer, the tractor has been in my family for four generations. I am now in the process of restoring my tractor as a 4-H project and...
  4. C

    830 COM pto cluch

    I am looking for some posible causes for why my pto will not hold adjustment. I have tightened the pto cluch twice now the first time I was going to use it on a corn picker and it wouldn't even turn anything over I had used it to unload a few silage wagons before and it seamed to work fine. I...
  5. C

    207 tach drive

    I recently priced one for my 830 through CNH at $117 but that threads into, and I'm not sure about the drive teeth. How does one go about replacing this? It looks kind of difficult with the filters, pump, and lines on the same side.
  6. C

    More problems with Case CK 830

    I ordered mine though case I beleve it was part# H749218 but you might want to double check that. I know it didn't cost over $15.00 Austin
  7. C

    More problems with Case CK 830

    I recently replaced my pto and axle seal on my 830. I drilled two holes on opposing sides of the seal then threaded skrews into them and pulled the seal out with a vise grips and pry bar. Worked as slick as pledge on a lanolium floor! Austin
  8. C

    What was the first Case tractor you drove, and how old were

    After years of riding (sleeping) on the floorboards Dad let me sit on his lap and steer the 7120 magnum. At the age of about 5 or 6 I was promoted from the lawn mower and four wheeler to the 500b, only drove it from the hay elevator to the shed but it sure made my day! I was 8 when I got to...
  9. C

    Need CASE 730 Engine

    As of early August there was a diesel 730 comfort king at Colfax tractor parts in Colfax IA. They said the engine was good, they weren't going to part it out but someone Made an outragous offer on the wide front. They also said they hauled it in from California. Austin
  10. C

    Tank Heater?

    I have a 1500 tank heater on my 830 diesel. It is plumed so the heated water enters the manifold on the back end of the engine, which would be fine but it opens the thermostat and heats the radiator before it heats the heads or the block. Is this the best place for it or should I plumb the hot...
  11. C

    Case-O-Matic presure relief valve?

    Thanks paul! I just wish she would start a little easer, but I was told all 301 diesels were cold blooded. Where abouts are you located in w,il I might have to take you up on the parts offer if your close enuf, I have a good sized list made. I saw your 830 in the galery! Sure is a sharp...
  12. C

    Case-O-Matic presure relief valve?

    Thanks loren, Im working on a 831 which should be about the same setup as a 800B I think. I removed the pump, filter assembly And noticed the valve was stuck about 1/4 of the way open, I tapped the top and it went back in to place I think some filings might have held it open. The spring seams to...
  13. C

    570 Diff Lock Seal?

    Clear packing tape works good also, if you want you can even put a little grease on the tape too. Austin
  14. C

    Case-O-Matic presure relief valve?

    How much spring tension should a case o matic relief valve have? How do i get the snap ring off to replace the spring if needed? Thanks: Austin
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top