(800) 853-2651
SHOP NOW

Recent content by CBull

Yesterday's Tractor Forums
  1. C

    is there a glossary for the shorthand you all use ?

    REMF (Rear Echelon MF'rs); heck no, gotta' be out front... so far out there in fact, we commonly worked behind and amidst the bad guys. CBull (retired 82nd Airborne paratrooper)
  2. C

    Choke rod pull help please?

    --- I agree that a carry all sure is handy, not real sure how I did lots of stuff with out it. CBull
  3. C

    '59 871 carb question

    Tap on the bowl a bit and see if the needle then seats (leak stops, might be the needle not seating, leak keeps leaking, might be the float). Or just wait for the kit and rebuild. CBull
  4. C

    600 PTO Shaft

    Replace the PTO shaft seal. Spring side toward the oil. CBull
  5. C

    OT Skunks

    Pipe trap is easier than a box trap and blanket. 6 inch stove pipe or PVC pipe and make your own doors for one end or both ends, rig up a door trigger and toss in some bait. The 6 inch pipe is small enough that the skunk has a hard time or can't spray at all, also dark inside so the skunk...
  6. C

    Dearborn 2 bottom plow for sale lower michigan

    Might be interested, need some details though. CBull
  7. C

    Gardner Denver air compressor pump question

    SG; you might get lucky at the manufacturer website; http://www.gardnerdenverproducts.com/compressors/ Their ContactUs link is just a darn form though. CBull
  8. C

    Tractor shuts down

    New fuel line routed near exhaust or engine? vapor locking... CBull
  9. C

    Jubilee Carburetor

    --- May just need to look closer at your carb brass tag??? Stamped numbers can be very lightly stamped or worn. My NAA carb brass tag has TSX followed by two separate numbers: 753 then 428. Could both of our barbs actually be TSX428 or not? CBull
  10. C

    Greetings , and Help !!!

    OK, I didn't see the very last post, but vapor locking seemed to be the source of the symptoms. Hmmm, issues surface after an hour of use..vapor locking? Is fuel line routed near exhaust? Try insulating the gas line that runs near heat source. -CBull
  11. C

    Temp Gas tank -tburch

    --- Good "taste". -CBull
  12. C

    NAA sheet metal reinstall

    Yep phillips head (#2 or #3?), 5/16 - 24 screw. CBull
  13. C

    NAA sheet metal reinstall

    Thx guys, that's what I needed. CBull
  14. C

    Strange ford 8n voltage regulator issue

    Assuming your numbers are from the dash ammeter... do you get similar numbers with a multimeter? If yes, then we have some digging to do. If no, then swap out dash ammeter. Since this tractor is new to you; Does the wiring in general look good or need some work? -CBull
  15. C

    NAA sheet metal reinstall

    Sounds good guys... keep 'er loose, until the end. Any idea what the original tin to tin screws were? I'm missing most of them. Assuming flat head slotted screw, but what size? -CBull
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top