(800) 853-2651
SHOP NOW

Recent content by ccaissie

Yesterday's Tractor Forums
  1. C

    9N Grader?

    Looking for a rear 3 point blade. Tractor Supply has one for $600 think I could get mmy drive done with just the rear blade.
  2. C

    9N Grader?

    I have a 1/4 mile driveway that needs some reshaping, probably more work than a back blade, but between a grubhoe and a 3-point blade should be able to gradually get it in shape. So next question...who has one of these in the Central Maine area? Where's the local tractor club? Since I do...
  3. C

    9N Grader?

    Anybody ever use their 9N for road grading, touchup? Was there ever an attachment available...Front, Belly mount? I know there were snow plow and york rakes.... Sources?
  4. C

    Cub freeze and burst issues

    Cracked head.... water jacket and of course, the bolster for the radiator mount. I can get this cub for a song, but maybe it's too much problem. I intend to use it lightly around the property. It runs, just cracked. The head can be replaced easily enough. I know JB weld will work for a...
  5. C

    Case 265 (IH-Case) no fuel from pump.

    I had the Case IH manual...not the best, but essential info is there re: clearances and torque. Runs like new, really nice.
  6. C

    Case 265 (IH-Case) no fuel from pump.

    The fuel solenoid wiring was actually never used...strictly manual shutoff. Forgot about that. So when I hot wired it, it was malfunctioning and shut the fuel off. Disconnected the wiring and all is well.
  7. C

    Case 265 (IH-Case) no fuel from pump.

    Just rebuit this 3 cylinder Mitsubishi K3H, and can't seem to get fuel to the injectors. Removed the glow plugs to reduce load when cranking. Cranked it so much, rings must be broken in by now. Pretty sure it all went together well, I will pull the injector pump side cover to see if the...
  8. C

    Ford 861 now won't start when pulled

    Was hard to start, now won't. Blew air back thru tank strainer, new filter, fuel gushes out. Broke lines to injectors, pulled for 5 minutes in hi gear, will not even squirt other than a drip or two. Intrigued re: something stuck. Will rap on it. Also will check for return line blockage...
  9. C

    Can't find CASE IH 265 offset in these forums. What is

    Compression test real bad cyls 2,3 are real low. Dumped oil in the glow plug hole, compression came right up. Later tore engine down....piston rings had been replaced on bad pistons, and oversize rings etc. not available. Top rings in cyl 2,3 were in many small pieces. Engine needs to be...
  10. C

    Discontinued parts for 1135

    Yes, that's the other variant called the Western, I believe.... I see the difference is in the flange holes on the vertical spindle. In the AGCO parts books, that is accurately drawn.
  11. C

    Discontinued parts for 1135

    That's interesting, this is a wide front 1135. i thought that I would find or make a bronze bushing once I got it apart and was sure there was not replacement available. So maybe it's the bushing I want and that's actually available. Thanks for the shout!
  12. C

    Discontinued parts for 1135

    Don't have the dimensions yet.
  13. C

    Discontinued parts for 1135

    I usually assume that if the seal is bad, there's an issue with the bearing...Haven't pulled it yet, lining up the parts for limited down time. I have back-traced parts before but this item has me stumped.
  14. C

    Discontinued parts for 1135

    Rebuilding a leaking hydraulic steering box on the 1135. I rebuilt the failed pistons, rings and cylinders, so steering is now restored. There is still a leak, must be the vertical steering shaft seal and/or bearing. There is fluid flow in and out of the box, so the lower seal is the culprit...
  15. C

    Ford 861-D won't stay running, lopes, stalls

    Cleaned tank, fresh filter. Hard to start, but lights right up when pulled. Good power at full throttle, tricky when lowering the throttle...sometimes dies. Any throttle setting below full, results in a loping/hunting. Then of course it straightens out. any buffer screw setting like...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top