(800) 853-2651
SHOP NOW

Recent content by CCMnNC

  1. C

    Unstyled John Deere A oil pressure

    I understood what you were saying about HF test gauge and looks like they offer two different brands at HF. The JD gauge on the tractor reads between the L and M. Thanks for the advice
  2. C

    Unstyled John Deere A oil pressure

    Does anyone know the actual oil pressure numbers on the unstyled John Deere A gauge what L M and H marks represent?
  3. C

    English made Ford 3000

    Are the original rear wings and foot rest for the english 3000's hard to come by?
  4. C

    English made Ford 3000

    I took the original rear fenders(mudguards) and both the wide foot rest off my English made Ford 3000. Are they the same as the Fordson Dexta fenders and foot rest?
  5. C

    Ford 172 Engine?

    Was you able to find out if they were the same?
  6. C

    901 injection pump issues

    Not sure if anyone has mentioned this yet but the fuel injectors return line that is under the valve cover can leak fuel into the crankcase. The solder joints can leak and fuel drains into the oil return holes or the push rod holes.
  7. C

    NO wonder I got it cheap

    I think you will need to pull the injectors there are bolts under them.
  8. C

    1968 Ford 3000 simms injector pumps parts

    Thanks I found them yesterday at this site and ordered the parts. Seems to be one of the only places to purchase parts for this SIMMS. Couldn't find the parts in the USA.
  9. C

    1968 Ford 3000 simms injector pumps parts

    Need a replacement plunger for the simms injector pump for 1968 Ford 3000. Number one plunger was stuck and the small tab on the bottom of plunger is broken.
  10. C

    1968 Ford 3000 simms injector pumps parts

    Their the wrong size need 8mm
  11. C

    1968 Ford 3000 simms injector pumps parts

    The ones I need are 8mm.
  12. C

    Ford 172 diesel oil pressure

    Thank you for the information.
  13. C

    Ford 172 diesel oil pressure

    What is considered to be normal good oil pressure range in a 172 diesel and what's considered bad.
  14. C

    FORD Four Speed

    I haven't looked to see if it has the plate haven't purchased the tractor yet.
  15. C

    FORD Four Speed

    Does anyone know if all the 58-64 four speed transmissions had the hydraulic tubes installed in them even if the tractor was an industrial model 20303 with no 3 point lift?
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top