-
C
Plumbing Loader Controls-Ford 4610
I am in the exact same boat. 1989 4610 with dual pumps and a 7210 loader. I want to add the joystick as well, so looking forward to the correct solution for this.- cemeyer
- Post #11
- Forum: Tractor & Farm Talk
-
C
Fuel injection pump on 1978 ford 3600 3 cylinder diesel
Not sure if this allowed, but I got parts for my CAV pump from here. I believe this is the part that you need. Very helpful site once you figure out how to navigate it. https://injectionpumps.co.uk/product/cav-dpa-short-straight-banjo-outlet/- cemeyer
- Post #27
- Forum: Tractor & Farm Talk
-
C
Ford 3400 3 cyl gas. Where is the engine oil going???
Looking a t messicks diagrams, your picture and the seal available on this site, I think it is a single seal, but double lipped, with a lip and spring facing both directions. -
C
59 981 gold demonstrator paint code and other questions
I do have another question. On the SelectOsSpeed decal on the hood, should the model number say 901 or 981? I've seen replacement decals both ways. I'm just curious which way it would have left the factory. -
C
Paint codes // Gold Demonstrator
I d be interested in the paint codes as well! Thanks, Curt -
C
59 981 gold demonstrator paint code and other questions
Good evening, I ve got a decent tractor that I d like to restore and continue to use on my small acreage. This last week it started off as replacing the rear main seal, now I m completely rebuilding the engine and I m very tempted to go through the whole thing including paint. What would... -
C
Time for another....
If I click on profile and go to contact, it shows no email and private messaging is disabled. -
C
Time for another....
Tom, I may be very interested in this tractor depending on price. Let me know what you’re thinking and I’ll discuss it with the wife. Curt -
C
suggestions with egged out axel
Dan, are you sure that your whole axle and bolster are different? After rereading Tony Jacobs description, I would say you have the heavy duty pin set up. I also believe I understand why the engineers designed the pin/bushing set up that you have, the way the did. It’s designed to have the... -
C
861 front axle
I picked up an 861 the other day. Someone, in its previous life, torched off the ends of the axle and the inner portion of both knees. Anybody know why someone would do that? I’d like to replace all of the hacking with good original parts. I’m planning on adding a loader on this tractor and... -
C
Ford Rest-o-Ride Seat
I’m very interested in these seat to add to my newly acquired 861. Is it still for sale? -
C
Ford 971 SOS shift cover caged nuts
McMaster Carr has them. CNH is spendy. -
C
Sos gurus, ??
Larry, after going through and adjusting all of the valves per the manual, I can maintain 4-4.5 lbs on the lube circuit. This is more than the 2 lbs that I had the other day. So I think I'll be good to go for a while, I hope. -
C
Sos gurus, ??
So I got the rear split done, the new pto seal in, the thicker thrust washer on the output shaft in and finally able to check pressures and adjust. Following the I&T manual for checking pressures, R2 should have pressure at all 3 servos. But I have none on servo 3, but if I go to 5-10...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy