(800) 853-2651
SHOP NOW

Recent content by Centerplate

Yesterday's Tractor Forums
  1. C

    International 584 wheel hub sleeve…

    Before you try to dig it out, compare it to the replacement seal.
  2. C

    What Is The Largest - Highest Hp Tractor You Put In Front Of. A Haybine?

    I run a 13 feet Case IH discbine with my Oliver 1850 at 9 miles per hour on a good straight field. It has a Dot 4 engine.
  3. C

    Another "what is it"

    It's better to have dirty hands than a dirty mind. As for the fuse puller; I have not seen one like this.
  4. C

    Another "what is it"

    I think I know the use for this, but not exactly for sure.
  5. C

    Oliver 77 Cracking Hydraulic Pump Center Plate

    When you put it back together, I would check the pressure on the system. No more that 1100 PSI.
  6. C

    Oliver 77 Cracking Hydraulic Pump Center Plate

    Greg Krush could be correct and the center section from your parts tractor could had had a very small crack not easily visible. The other possibility is the relief valve seat could have worked loose, but still held in place by the relief valve plunger. When your cylinder deadheaded the...
  7. C

    Bearcat Hammermill & Belts

    I am part of a group of guys that display at a local show and we have brought a Bearcat very similar to the one you have pictured. I am sorry, but do not have a photo in my picture files, but we did grind corn at the show with this mill.
  8. C

    Dating a Farmall Regular

    I have to say this relationship is going a little weird. Ha Ha
  9. C

    pto problems

    amsterdam, The PTO on an 8N Ford is on the left side of the transmission housing. Do you have an operators manual?
  10. C

    Oliver 88 Row Crop Rear axle housing.

    If I remember, the KA would be an assembly. It might have the bearing races installed.
  11. C

    Oliver 88 Row Crop Rear Axle Housing.

    I my memory serves me yet, "KA" might be an assembly with the bearing races installed. I cannot get the agco website to work for me right now or I would look it up.
  12. C

    Gears 77-880

    I sell centerplates for hydraulic pumps on these tractors. I also rebuild pumps and am in need of the gears in these pumps. I need good gears that are not rusted and not pitted that I could use in making rebuilt pumps. I am willing to pay some for the gears and for shipping...
  13. C

    Loader cylinders

    Baum is another choice
  14. C

    Loader cylinder

    You never know how many hours are on an Industrial machine like that 544B.
  15. C

    Draft link plunger oil seal question.

    I think the top cover has to come off to work on replacing the o ring. A service manual of an IT manual is going to be smarter that I am. Help in an International forum will have guys familiar with this tractor model. You are starting off correctly by doing research before diving into this...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top