(800) 853-2651
SHOP NOW

Recent content by [email protected]

Yesterday's Tractor Forums
  1. C

    CRANK PULLEY REMOVAL

    Fellas, I got the engine out of my M. It appears that someone may have welded the pin in that holds the crank pulley on. I cannot figure out for the life of me how to get this thing off. It has the extremelylarge nut around the shaft and the pin that appeared to be welded in, plus a small...
  2. C

    FARMALL M ENGINE CRANKSHAFT

    Gentlemen, I have just about got the engine out of my M. I'd like to start getting some quotes on machining, but, I have a few questions about the crankshaft: Does the machinist need to have experience with Farmall specificallt to be able to do this? How do I know if there is enough...
  3. C

    M engine rebuild, where to start

    Thanks so much for the input gentlemen. I'm looking forward to getting started on my project!
  4. C

    M engine rebuild, where to start

    This is my first go at this. I had a rod knocking, bad, checked it out and the crank has to be reground. The engine needs to come out to do this and the flywheel, clutch and all have to be torn down. So, while I'm in that deep, seems like to me I should just re-sleeve, piston, ring, crank...
  5. C

    Farmall M Knock

    Gents, I was out working on the M today and noticed a slight knock, is rapidly turning in to a BAD knock. At low idle, there is a knocking sound on the bottom portion of the engine. I'm guessing a rod bearing. Now the person I got the tractor from advised that he replaced a "bad" rod...
  6. C

    More Belly Pump Questions

    Thanks for the pics....BIG HELP!
  7. C

    More Belly Pump Questions

    Do the pipe connections just unscrew, or do they pull out?
  8. C

    More Belly Pump Questions

    Gents, Put some SAE in 30 in my belly pump. I actuated the lever and vwalla'....the engine bogged down. So I'm guessing this means that the pump is at least working, somewhat, no pressure check yet. Now for the bad news. When I actuated the lever, the engine bogged, then oil began...
  9. C

    Farmall M Belly Pump Test

    Ok, I'd like to test the belly pump on my M, but I have no implements or hydraulic cylinders...So? If I fill it up with SAE 30 and actuate the lever, with everything plugged....and the engine boggs......does this mean that its working? or Should I just leave it alone until I get an...
  10. C

    New Farmall M

    Gents, I recently purchased a Farmall M at a local farm I've been working at for some time. Owner traded me for $800 in labor. The sheet metal looks good, and the tractor runs good. Getting a little bit of blue smoke, but.... I have a few questions for all of you, I'm too new to post...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top