Recent content by CFB

  1. C

    8N Marvel-Schebler leak at the choke arm - again

    Thank you for confirming that gas should not be coming out the choke shaft. Thanks for the tip to try before assembling.
  2. C

    8N Marvel-Schebler leak at the choke arm - again

    Today was the big day when the tractor, now all assembled after several years of restoration, would start all up. It almost did. The two area I was afraid of worked, but the ones I didn't, well, didn't work. Several years ago, I had a flood of gas on the floor. It leaked out of the choke...
  3. C

    Added a fan shroud to 8N - attempt #1 failed

    Hello, So today was the test to see if tractor would start after reassembly. I had a gas leak, so that is another post, but it, a 1949 8N was ready to start but the fan jammed. I know I read on the forum that is why farmers took it off. I thought I had it really good. When manually spun...
  4. C

    8N axle bolts off , now to fit the bumper on

    After days of penetrant and breaker bar work, and jacked front end completely up, was able to get the two axle bolts out where I will mount the bumper. I bought two longer bolts, ready to go, but bumper does not fit. The "L" shape mounting end is angled correctly (Pic 1) I think to match the...
  5. C

    Installing a bumper on my 8N

    The bolt hole where I pointed with the black stick is where the bumper has to go. I held the bumper up to the axle and that is where it fit - same place on the other side. Going one hole over toward center, while you see a hole in the outer axle, the axle behind does not have a matching hole...
  6. C

    Installing a bumper on my 8N

    I figured a half inch longer as that is how wide the bumper frame is, I'll see what I have in stock. thanks
  7. C

    Installing a bumper on my 8N

    Hello, I'm getting closer to finishing up my 8N project. While I'm waiting on something, I thought I figure out how to mount the bumper I was given when I bought the tractor. I see the bolt holes I would use - I need to get a longer bolt now - but wondering if I have to jack the front end up...
  8. C

    8N Fender Light Bracket - Which fender to use?

    Thanks everyone. After all the talk my aftermarket bracket fit perfectly. While they came primed, I needed to get a spay can from parts to match the fenders. Sorry, don't know why the photos got turned. I have no space behind the dash on the right side. I'm satisfied how it turned out.
  9. C

    8N: two questions: springs and pedals

    Hi. Its been a while since I did this as worked on other areas, but I thought I forgot the 3rd left side only spring. But it is there. Do I have the correct three springs and in the correct spots on the left side 8N brake? I think I followed the parts book, last picture, part 2299 only used...
  10. C

    8N Fender Light Bracket - Which fender to use?

    Thank you for this. Makes good sense and reason to go left. I did look in the parts book before but now studying it a bit more, it is on the left. Seems like that transmission housing hole should have been on the left side too.
  11. C

    8N Fender Light Bracket - Which fender to use?

    Hello, One poster to my earlier question on mounting the bracket, I think showed his bracket on the right (looking forward) fender. All other videos I've seen shown it on the left side. When on the left side, it routes by the brake rod, then behind the seat to the right side and through the...
  12. C

    8N fender brackets for mounting lights

    Thanks for the picture. So you did not have to drill a new top hole - it fit to the hole where the fender and steel brace behind meet?
  13. C

    8N fender brackets for mounting lights

    Thanks for your thoughts. While I probably could bend it, I'm not convinced I could match the top hole. I hate to drill another hole but I think that is the route I'm going to take. I have one idea I'm going to try about making a short spacer/extension just to see if that would work. I...
  14. C

    8N fender brackets for mounting lights

    Hello, My question relates to the fender bracket. It seems the bottom of it fit the same two holes used for the fender brace behind but the top hole just doesn't make it. Fenders needed work but I thought I got the contour pretty good. Don't know if I should bend the top part of the bracket...
  15. C

    Considering a 1950 JD M with plow

    Thank you for your guidance/feedback expecially about the hitch.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top