(800) 853-2651
SHOP NOW

Recent content by Charles Krammin

Yesterday's Tractor Forums
  1. C

    Points quality going down hill

    I just bought blue streak from NAPA for my 2N. Had to file holes to get screws in. Could only adjust points to >010. Had to bend to get .015 gap. Also have been burning up 12 volt coils for the 2N from Tractor Supply. The box says "2.8 ohms. No directions included as to need/ no need ballast...
  2. C

    Ford 600 front pivot pin discovery.

    Pulled the front axle support pin on 1958 Ford 600. It unscrews, using something in the slot on front to keep it from unscrewing. Only 1/8" screwed in back support and bearing support was on threaded portion., which wore 1/8" deep. Plan on brazen worn spot and file down and relocate wear area...
  3. C

    Cant Keep Ford Golden Jubilee Running? Gas starvation?

    unscrew the plug on bottom of Carb. Watch for consistent flow. Poor gas flow problem (similiar to yours) was crud in tank not able to allow gas thru upright screen in the tank on my 600. Poor design allowed crud to stay in tank for 50 years. Mine only acted like yours when I worked real bumpy...
  4. C

    Fertilizer hopper parts needed for 1929 IHC planter

    See if I can get seed covers
  5. C

    Fertilizer hopper parts needed for 1929 IHC planter

    I'll try and upload some current pictures of my [lanter
  6. C

    Fertilizer hopper parts needed for 1929 IHC planter

    My original post of the picture of the agitator (Pan) with gear teeth on bottom, the scrapper with down spout. and remanats of can, needed. This plater can be identified with diecast seed covers, with IHC enbelezed (collectors item). Marker attachs to rear center and swings overhead of operator...
  7. C

    Fertilizer hopper parts needed for 1929 IHC planter

    Yes I have the check wire and rewind reel. I have freed up all bearings I tried to check row my food plot last year. The return spring was weak and didn;t close drop gate, putting a screen door spring inside regular spring this year. NEED HELP FINDING REMINANTS OF CAN, AGITATOR etc, If I can;t...
  8. C

    Fertilizer hopper parts needed for 1929 IHC planter

    I have this rare 1929 IHC check row fertilizer (down tubes move) and hill planter. The galvanized tubes are like new as the PO removed the cans, plates, and scrapper I would like to buy replacements or find someone who has a scraper? Here is a picture of what they look like.
  9. C

    Earliest 9N Serial Number in Existence?

    This might be me sitting on the hood of our first 9n. Note 10"rubber Had wheel weights in rims. Note hub outside rim. Thats the way my brothers fixed it when it busted an axle in Lake Michigan, slip scrapping gravel. It was kind of hard as the tires were also loaded. Bought in Allegan Mi with...
  10. C

    OT - Lost my soulmate yesterday

    Royse I'm so sorry. I enjoyed her very much in our visits. PS On the 600, I finished painting the rims, hat caps and the Case wheel weights and plan on putting them back on (but not sheet metal) and plant the food plot in Fennville in May, be for I bring it for red paint. My soulmate now has...
  11. C

    Made the 2N pull a semi out

    How do you take pictures with your cell phone when your"re busy working? plus this site makes it very hard to post when the site they use made it impossble to economly post?
  12. C

    Made the 2N pull a semi out

    I rode shotgun on a parochial 1951 chevy stubnose reincarnated interurban Transport. Simce I know more about about vehicles, than the driver. 4 brother off to WW II, dad on mail route-mom in cannery factory, I did most of the farming with a 39 Ford Ferguson. Things I did on the bus that OSHA...
  13. C

    Made the 2N pull a semi out

    Invotative ways I make my Ford/Ferguson pull there MAX Just got the 2N ready just in time to pull a cattle semi tractor/trailer out. J-1 snowplow-Logging tire chains on-loaded tires- draw bar at 24". 9" snow overnite in Hastings MI. Semi loaded with "Charlouise bulls for Texas. Trucker tried...
  14. C

    Charlton Park URL

    Fordson, Ford Ferguson, Ford featured tractor at annual Barry county Gas $ Steam Club show at historic, Charlton Park Village 4 miles East of Hastings MI. I will have my 1945 2N with Dearborn J-1 Bulldozer attached, and Ferguson solid shand cultivator attached at rear 3 point, with Ottawa side...
  15. C

    Charlton Park URL

    https://search.yahoo.com/search?ei=UTF-8&fr=crmas&p=charlton+park+hastings+mi Then go to events and PDF flyer on show Charles Krammin
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top