(800) 853-2651
SHOP NOW

Recent content by Chaz7795

  1. C

    Rolling under nature's Fertilizer.

    Your welcome. I dont know, Ive only had varying degrees of success at posting videos of any kind recently.
  2. C

    Rolling under nature's Fertilizer.

    ttps://forums.yesterdaystractors.com/videos/mvvideo65144.mov[/video:a0e5d44cfa]
  3. C

    Got out the plow one last time for 2020

    Thats my dad setting on the back. He was setting there because he was filming. [video play=false:d74217a91b]https://forums.yesterdaystractors.com/videos/mvvideo64580.mov[/video:d74217a91b]
  4. C

    Got out the plow one last time for 2020

    Ford 3600 pulling 3-14
  5. C

    Got out the plow one last time for 2020

    Thanks SV Ill give her another try in the morning.
  6. C

    Got out the plow one last time for 2020

    I have a short video and a few pics I tried to share on this thread, but for some reason they dont show. Ive posted pics on these forums before, but having trouble now. I go to the upload photos/videos section chosen the files from my photo library, and then hit preview and nothing shows. I did...
  7. C

    Got out the plow one last time for 2020

  8. C

    Got out the plow one last time for 2020

    I can pull 3-14s with a 3600 ford here in northwestern NC.
  9. C

    43 years ago today

    Sorry I replied to wrong post, but just the same.
  10. C

    43 years ago today

    Im also older than you, but 43 years old. I was born in April of 77. Happy Birthday by the way.
  11. C

    8N Draw pins

    Sorry wore out I should have been more specific, the lift arm end of the pin was what was worn. You may very well be right copperhead dont play, hadnt considered that. I think well just order a set from this site and see how they work. Thanks for the help.
  12. C

    8N Draw pins

    Hello gentlemen, Ive posted a few times on the ford forum, I believe this is the first time on the N forum. Me and my dad are working on his 50 model 8N and have the axle trumpets off, so we were going to replace the old draw pins. He had a new set he had purchased some time ago for just such an...
  13. C

    Ford 3600 voltage regulator

    Thanks for the advise Farming Engineer. I got home this evening and got done working on my tractor brakes I cranked it up and drove it to check on my adjustment, and oddly enough the battery light was off. I thought maybe bulb had burnt out but it hadnt, it comes on when you cut the switch on...
  14. C

    Ford 903 post hole digger

    I believe Danuser made the gearboxes for the Ford diggers.
  15. C

    Ford 903 post hole digger

    Ive got an old red Ford 903 digger. Theyre very good old heavy duty digger in my opinion. Im not sure of exact ratio, I would say that they are around 3 or 4 :1 most diggers are I believe. The biggest auger listed in parts manual is 24. If you look online I believe you can find parts and...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top