Recent content by claude720

  1. jd2cyl1943

    Update 13

    I got the tractor jacked up to get the tires off. I'm bit behind schedule..... Found some nice JD Green under old grease. I gave the front end of the tractor a good washing. I sprayed out the radiator fins to clean out the dust. They look pretty good. I'll be reusing...
  2. W

    Sway block

    Need a left hitch sway block for a 2640, know of one available from a 3010. Are they the same?
  3. chuck machinist

    Magneto service Manual

    I did a little rummaging around on the Internet today and found a nice case mag service manual CM
  4. kcm.MN

    2022.10.19 Rust Pic

    Puzzle: https://jigex.com/DmoVd
  5. A

    880 temperature gauge

    The temperature gauge on the 880 gas has stopped working. Where do I begin or is it easier just to buy a new gauge?
  6. Tony in SD

    Is there any interest in prototype tractors?

    My brother has a JD articulated 4 wheel drive tractor (sorry, dont remember the model) that he was having trouble finding parts for. Turns out it is a prototype that escaped somehow. He was wondering if there is any collector interest in such a tractor or are escaped prototypes a common thing?
  7. C

    Case 430 gas engine exchange

    Have a 430 gas with hole blown through #3. CWG K110 cast into the block behind distributor. Found gas swather with CWG E64 cast into the block. both are 3 bolt starters and both are approx 19 back to front of block. Will they exchange or is more info needed? Many thanks in advance.
  8. C

    Case 930 injection pump: Follow Up

    Took the rack cap off and moved throttle...nothing. The head of the allen head was approx flush with the pump housing. I gently pushed the rack towards rear of tractor and it moved easily approx 1/4 maybe more to what I would call all the way back. Moving throttle linkage, the rack will not...
  9. C

    Case 930 injection pump

    back home and took off rack nut. shown in picture....moving throttle from idle to WOT the bolt head moved maybe about a total of 1/8.
  10. C

    Case 930 injection pump

    Many thanks to all of the support and advice. The rack nut is one on the radiator side of the pump correct?
  11. C

    Case 930 injection pump

    didnt know if Dieseltech or others could help me but just brought home 930. It had run a few years ago then sat outside. Changed fuel filters and put new fuel in. Broke all 6 lines loose at the injectors. Tried to pull start around the yard. Got good fuel out of 1,2,4. Closed down Lines 1...
  12. C

    730 Frozen throttle linkage

    Have a 730 gas that has the pin between cast frame frozen. I have unhooked all linkages and all are free except pin that rotates connecting the foot and hand throttle and linkage to carb. I have heated cast I have heated shaft I have been spraying penetrating oil of all kinds for months...
  13. R

    2950 Wiring Diagram

    I am in need of a comprehensive wiring diagram for my 2950. It's not in the I&T shop manual. I used to have a 4050 that I needed a wiring diagram for, and even the Mother Deere manual didn't have it for that tractor, either. There was a *thick* shop manual I found online that was well...
  14. W

    ford 801 smoking by hydraulic pump

    My 801 Ford usually runs great but after letting it set for over a month or so without using it, It smoked terribly on start up and cleared up after a minute or so. I could not see where the smoke came from because it was so great but it appeared to come from the area around the hydraulic pump...
  15. Don L.

    Case Poster of the Case 3294, pic

    27 x 27 Dealer Poster of the Case 3294 , Built two years 1984 and 1985
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top