(800) 853-2651
SHOP NOW

Recent content by coggonhick

Yesterday's Tractor Forums
  1. C

    3 bottom plow

    If you have a Funk kit in your N you might be able to pull one, otherwise good look.
  2. C

    Plow parts

    Howdy everyone! I was plowing my neighbors field and all the sudden "SNAP", the shear on my 10-1 plow broke in half. Im looking for a new shear and moldboard so if anyone knows where I can purchuse a shear and moldboard, please help! Thanks! Coggonhick
  3. C

    Possible manifold leak??

    I had a leak in my manifold once, the engine was not running corect and when we were turning over the enignes, listing to every noise, we hurd a hissing from the muffler. When we took the muffler off we still hurd the noise so we cut the manifold in half. we put a lightbulb in the intake section...
  4. C

    8n

    When you disasembled the engines, you shouldve found a cam thrust washer infront of the camshaft. When I took mine apart it didnt have one and chipped the cam gear and the case. We put in the part and think that the problem is solved. First, see if you have that part, if you dont look around for...
  5. C

    8N carburator

    For the longest of times after I rebuilt my 8N the engine never sounded like it should, and when adjusting the carborater there would be no diffrence. Then when turning over the engine I herd a hissing sound coming from the muffler. We already replaced the muffler so we replaced the manifold and...
  6. C

    Sawmill

    Im restoring a sawmill for the local historical society and am planning on running it off of a belt pully connected to my 8N. Do you think the tractor has the muscle to power the sawmill??? All imput is welcome!!
  7. C

    Help me identify my dad's tractor, please

    What you have lookes like a 1947-1949 8N tractor. If you remove the paint on the engine block next to the oil filter housing you will find the serial number. Also, the sheet meatel is from a 8N ford, so if it says 2N, like on mine, its probably just the casting numbers that never changed or...
  8. C

    zenth carb housing can it be welded ?

    Cast iron cannot be welded with a wire welder easily, you would need to take it to a special shot to have it welded for you, and that might deform the shop, try going to a salvage yard and pick up a new carburetor or even just the peace that broke.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top