(800) 853-2651
SHOP NOW

Recent content by Collosse

Yesterday's Tractor Forums
  1. casecollectorsc

    Re: 2670 powershift problem

    Ouch!!
  2. tomstractorsandtoys

    IH 86 series narrow front?

    Up in Tractor talk there is a post about narrow front tractors and a remark was made about 86 series narrow fronts. Does anyone have a pic? I am not disagreeing but would like to see one. Thanks Tom
  3. N

    No metric wrenches?

    Twice in the last six months this has happened. It shocked me both times. I bought an aftermarket fuel pump at Napa to replace the mechanical one on my chore pickup. It wasn't cheap but I was glad to see it was made right here in US of A. When I started putting it on ALL of the fasteners were...
  4. R

    Look what we just got

    Newborn Angora Goat - born this morning at the Carrot Patch Farm. We had another born two days ago. Both doing OK!
  5. jon f mn

    today's funny

    .
  6. C

    tires

    Anyone ever put 13.6 tires on 14 inch rim for pulling? Have any luck ? Good or bad? Thanks for responses. Carl.
  7. D

    Snap rings for H

    Anyone know of a more affordable source for piston pin retainers than Deere for an H(H214R)? I have new .005 oversized pins and would rather not reuse the old snap rings if possible.
  8. K

    GEHL HL4400 BUCKET GOES DOWN BUT NOT UP

    I have a Gehl HL4400 skid loader and was wondering if anyone has had any ideas on why the bucket has no lifting power to curl the bucket. It has a set of forks on it right now i was carrying freezer panels to load on a trailer when i went to pick up another stack when i went to lift the forks...
  9. A

    Looking for Paul Olson from Bottineau ND

    I need to get in touch with a fellow from Bottineau ND that moved away from there, Hid Dads name is Bud OLson and had John Deere dealer ship years back, Paul is his son and I would like to get in touch with him, If anyone knows a phone number that would be great.....
  10. J

    720D Pony motor John Deere

    Pony motor starts & idles fine. When the "Run" lever is slid left - it should rev up to high speed, but it is very lazy, sometimes it sputters to nearly stall and needs teasing to get up to what (my ears say) is cranking speed. I have been tweaking the main fuel jet screw counter-clockwise in...
  11. R

    engine stand

    any tips on doing an engine overhaul without an engine stand. i cant find one anywere. im ready to pull the engine off and am contemplating the best manuever. thanks
  12. C

    John Deere M

    Mornin ALL I'm new to the site, but not new to tractors, I'm the proud owner of a 1949 Ferguson TE 20, and my most recent find a 1950 JD"M", and this is no kidding , it was in a shed covered with a tarp ,hasn't been started in at least ten years,,all original good paint and air still in tires...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top