(800) 853-2651
SHOP NOW

Recent content by Confederate general

Yesterday's Tractor Forums
  1. J Hamilton

    Questtion for the plow experts

    Was at an auction today with Tgrasher and we noticed this plow with chains just ahead of the moldboards. The chains show lots of wear so it had been used this way but we couldn't figure out what the purpose of them would be. Has anyone done that before or know the purpose of them?
  2. JohnRowehl

    White disk harrow

    Saw a WFE disk sitting along the road the other day that caught my attention because it looked very much like the Oliver 252 disk that was on the farm I grew up on. The decal on this one was 256. Just wondering if there was a modification or if it s the same thing and they just renumbered it...
  3. kcm.MN

    2023.09.20 Rust Pic

    Sullivan power unit Puzzles: https://jigex.com/SFRoj https://jigex.com/bhU8v
  4. T

    IH 384 fourth gear split

    I have an international 384 with worn quill gear bearings. Do I have to split the tractor at the engine or can I just split it at the clutch housing/transmission.
  5. D

    Quick hitch for 3-pt

    Have a 420W and a 520 with narrow front that I use with a couple of 3-pt hitch pieces, mostly a two row cultivator and a small back blade. They can be a bear for me to hook up by myself and would like to put a quick hitch on one of them to simplify the process, probably the 520. Do I need a...
  6. 7

    706 control valve tube

    I think I have some ideas on what to do here but taking one chance someone might have a suggestion. My left valve here leaks out center hole and will be replacing o-rings. Hex nut comes out but pipe doesn't turn. Right pipe will come loose with nut. But that one doesn't leak. If I take that...
  7. R

    600 lift cylinder / cover vs NAA

    Hey all, I ve been searching and I haven t been able to find an answer.. does anyone know if the lift cover used on the 600 is the same as the one used on the NAA? I know the 600 has internal hydraulic lines and I read one comment that said the NAA had the same lift cover as the 8N, so maybe...
  8. E

    Never trust a spark plug

    I spent two hours this morning chasing fuel starvation symptoms on a Honda pump motor. At one point I had the plug out and saw spark where I had it grounded to the motor instead of at the electrode. So put a new plug in and solved the issue. Engine ran great with the old plug for about two...
  9. J

    Disc size

    What would be a good size disc to pull behind an 860? Assuming a good running engine and proper tires. Currently using an old Ford 6 1/2 foot 3 point. Would like a wider, heavier pull type.
  10. C

    Old IH 249 corn planter

    Are there any videos on how to setup and go over the older planters like an IH 249 corn planter , I want to plant corn with it this yr but it was rigged for planting pumpkins , guy took a corn seed plate and bored holes into it then put fiberglass over the other holes , I have other plates for...
  11. 560Dennis

    Bischoff interview

    https://engineperformanceexpo.com/mini-series/episode-53-engine-builder-interview-tony-bischoff/?utm_campaign=Newsletter-011623%20%2801GPKCAF2EZQJW4JE1TPSRJZBR%29&utm_medium=email&utm_source=Klaviyo&_kx=igmdGIQjzW31g4lMTA9HgERAMDi8BjVdsxC21j_ljLw%3D.MUWfay Interesting to see Lake and Joe so...
  12. T

    Oil filter for ferguson TO20

    What Baldwin filter works for a Ferguson TO20? P40?
  13. H

    544 Power Steering

    A friend bought an International 544 Hydro gas tractor. Does it have a power steering pump or does that run off the hydraulic pump? Thank you
  14. S

    how to check for a short circuit in a motor?

    I used my cheap voltmeter. I set it to ohms on the 2000 range. One probe on the black wire and the other probe on the white wire. It read 001. I then did the same check on my electric hand drill. It never moved from the 1. I am going to assume that the motor was shorted out. It was on a table...
  15. C

    510 grain drill

    I have a rope trip drill with drag chains. Am curious on how to set the planting depth. The manual does not specify
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top