(800) 853-2651
SHOP NOW

Recent content by corchel1942

Yesterday's Tractor Forums
  1. C

    2N over charging?

    Yes, now that I read it, it isn't very clear. handheld digital voltmeter reads between 8.55 and 8.90 with tractor running at 1/4 throttle, measured at battery posts. I have the generator turned down as far as it will go. As for the amp meter on the tractor, it reads just under 10. I don't...
  2. C

    2N over charging?

    Yes, the variable amp screw on the back of the generator is working, as I turn it up at night when I'm working it with the lights on to keep it on the positive side of the amp gauge.
  3. C

    2N over charging?

    Forgot to write, adjustable generator screw turned all the way down, and original amp meter on tractor reads just under 9, hand held reads about 8.5, but its a digital one and they don't work well with generator. That's being read at battery posts. This is a positive ground setup.
  4. C

    2N over charging?

    Restored 1945 2N, 6 Volt system with cut out and 1 wire generator. I just had to replace my battery, it was leaking around the battery posts and stopped holding a charge in a very short time. My question is about the charging system, and am wondering if it could be possible if the generator is...
  5. C

    flywheel on 8N

    Posting this to help a friend. Has a newly rebuilt side mount dizzy engine. Putting on flywheel and cant figure out where the timing marks go in relation to the crank and postings. Wasn't marked when removed. thanks Corey
  6. C

    Oliver 60 exhaust

    Thank you for the reply. Yes its a HC so I need to get the 28" Corey
  7. C

    Oliver 60 exhaust

    Just installed new factory style muffler on the 60, does anyone know the correct length pipe and inside diameter? Thanks Corey
  8. C

    Oliver 60 parts

    Thanks for the pictures. Choke lower left, ignition switch right side inside, and lights outside right, correct? I will check out Steiner for parts, I deal mostly with Korves if I can. Corey
  9. C

    Oliver 60 parts

    Working on getting my 1941 Row Crop 60 back up and running. Looking for front wheel seals ( or dust shields, whichever they used.) Tried Korves, no luck. Are these available anywhere? Also if anyone has a picture of the dash, I am trying to figure out what spot and what the ignition switch looks...
  10. C

    Ford Plow on CL $125

    Royce, I actually called the seller on this plow today to see if it was still available as I'm not too far away. I'm just south of Kalamazoo. Didn't have much time to ask many questions, but I am wondering what model plow this is. Are points and mulboards available? Might be worth going to...
  11. C

    2n cutout

    Update on the charging situation. Got home after work and fired it up and charging fine. Didn't change anything or tap on the cut out. I'm still thinking I had sticking points. keep a close eye on it, I might do the diode changeover in the cutout if I keep having issues. Thanks for the input Corey
  12. C

    2n cutout

    1945 2N 6v original style wiring harness, rebuilt generator (one wire)inbeen using well and charging correctly last 5 months. This morning started and showing no charge. My digital mutimeter wont work, picking up an analog today. Still using original cutout, and my first thought was sticking...
  13. C

    generator adjuster

    Looking to find the band style generator adjuster for my one wire generator. Need the complete assembly except for the bracket that mounts on the head. can't seem to find one not attached to a generator. Thanks Corey
  14. C

    How did your 6V start this morning?

    Well, its -9 here in SW Michigan and I decided before leaving for work to start the 2N and use the rear blade to clear the drive of snow(only 3-4 inches here right now). Was pleased with how well it started and ran. Just finished restoration on it late fall, and never having a tractor on the...
  15. C

    2N Transformation

    With all the help I have received over the last year I wanted to put up a couple pictures of the almost finished 1945 2N. Lots of little things left to do, install wheel weights, decals, front bumper.. but its back up and running. Thanks for all the questions answered and ideas. My son in the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top