(800) 853-2651
SHOP NOW

Recent content by cornerpost

Yesterday's Tractor Forums
  1. C

    farmall m hard start

    Had a 1952 or was it a 1953 H like that. By serial number 300 from last H built. After a lot of WTFs I had an Electric shop in Racine Mn go through starter. Now it starts on first or second revolution. Starter was sucking too much juice leaving a poor spark.
  2. C

    Farmall 450 priority valve

    In the early 1970s dads 400started having hard or non-existent power steering. Good parts man said dead head remote and see if better. Dad just put on new flow control valve if memory serves. My Dad and brother did the repair while I was on National Guard duty. They succeeded as it worked after...
  3. C

    Oliver transmission woes

    Bought. Farm all Super MYA once. There was enough water in the rear end that it froze and locked bull gears. I removed rat drain plug and there was ice. Warmed up and out came few gaskins of water.
  4. C

    Winter Oil

    IMHO a good multi-weight even a synthetic 5-30. Just my thoughts not an engineer.
  5. C

    Farmall H Not Starting... Spark, Fuel, No Start

    Had a 1952 H that turned into hard starter. New wiring harness and tune up items minimal change. Sold to neighbor. He took starter off and had it gone through by the shop in Racine MN. Now it starts first time over. Starter was drawing too much juice and spark was weak.
  6. C

    Medicare

    Open enrollment until Dec 7 I think. Insurance companies love to sell Advantage plans.
  7. C

    4020 wheel weights

    I have 4 sets of 8 1/2 inch weights on a 4440. Just got them little over a year ago.
  8. C

    4020 wheel weights

    Correct weight for 4020 is the Z-style weight with 8 1/2 inch opening. Think the larger 91/2 inch opening Z weight came out in late 30 series tractor and would fit over nine bolt dual hub. I have read that there are actually two slightly different 8 1/2 inch Z weights. They will all bolt up to...
  9. C

    John Deere 3010

    Take starter out and clean all crud out.
  10. C

    Seized (but not) Engine - 1956 100

    If you ever have to split it put in new ring gear. They are pretty cheap. Also starter drive. While starter is off go through it and clean up. Good for another 50 years.
  11. C

    Dad brought the last wagon home last night

    Cherish the memories.
  12. C

    110 /115 disk ?

    Brain just kicked into gear after coffee. Think I had a 230 disk. IIRC model 235 had bigger bearing hanger bolts. All other comments still apply.
  13. C

    110 /115 disk ?

    Had a 210 20 ft disk. Spring loaded scrapers worked great until the spring would break. Carried extra springs, hammer, leather gloves punch and roll pins or cotter pins to change spring. But my biggest dislike was the 5/8 inch grade 5 bolts that fastened the bearing standard to rectangular...
  14. C

    720 rear wheel clamp

    Make sure the jack screws that push on wedge sleeves to loosen are screwed out enough they are nut hitting sleeve when you try and tighten.
  15. C

    720 rear wheel clamp

    I am pretty sure that is a 3 1/8 inch axle. Pretty sure that the sleeves from a New Generation tractor with 3 1/8 inch axle have a different taper and will not work in a two cylinder wheel casting. Others will know for sure.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top