(800) 853-2651
SHOP NOW

Recent content by correct

Yesterday's Tractor Forums
  1. C

    wd straight shifter

    I really need some demensions for a repair. looks like a new one is out of my price range and cant find straight ones from the ball center how long is it to the tip of the bottom ,and the end must have been roundish in one plane and flat in the other . one flat side faces the orientation pin...
  2. C

    Wd 1950,s stuck shifter how to

    J do you know the dimesion from center if shift lever ball to end? and how wide is that end,? I'm tryng to fis a shift lever that gets lost from the right position on the linkages down in there-frustrated i measure my set up at exactly 5 inches length X 1/2 inch wide at tip-if I get this right...
  3. C

    WD shifter dimensions needed

    whats length canter of ball to end (new) and whats width of the end ? mines getting "lost" loosed contact with the works in there ,and has to be built back up to orig size Im fighten it and need to plow sno, Whwn I took shifter out the washer under snap r had a rubber O ring in it it this orig?
  4. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

    jim a kid here at the shop thinks you can see pic now, yes I can rotate the gear and chain with a pipe wrench but cant get the top tooth to release after it cycles (the one on the bottom does pull away each has a spring to make them drag on the gear so they can engage when rotateded a...
  5. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

    Heres the pic
  6. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

    sorry about very little verbage about the problem ,I attached picture of the chain drive wheel which has two teeth that can engage it and rotate it based on a cam is ( three times movement per wheel revolution) The cam is on the backside if that side wheel --the teeth wont let go after...
  7. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

  8. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

    Jim sorry dont know model barely can read mfg but sure is MA not an Mc Probly late 40's my email is same is when I signed up to forum years ago [email protected] not a g mail
  9. C

    have a wheel driven manure spreader -and cant figure out whats wrong -chain wont advance cause top gear wheel pusher sticks and wont cycle right

    Preview attachment 20251025_152623.jpgPreview attachment 20251025_152623.jpg 20251025_152623.jpg 4.9 MB
  10. C

    loaders / skidsteers

    just found out Ford 1.6 L industrial or the Kent version , used in bobcat, clark,maverick,ghel units in late 70s can have a 1.5 inch block heater installed (600 watt) one with 90 degree bend in the element works fine. in the right side soft plug,This is listed no where in searches nor in...
  11. C

    kohler 10 hp

    thankyou thats the issue i feel . I tried to get a new fuel pump but discontinued and the generic one sent me was jerry rigg install at best . So i asumed gravity flow ---yesterday I removed the strainer on the shut off, left in my installed 1 inch dia. in line filter and remodled the fuel...
  12. C

    kohler 10 hp

    kohler generator 10 hp --fuel pump failes but tank is on top so ran line direct, but it starves a little at times is line to small ? tank filter is ok ,i did add in line is that too much resist?
  13. C

    J D 1.5 E restored from N Dakota--need mag re magnetized

    thanks everyone
  14. C

    J D 1.5 E restored from N Dakota--need mag re magnetized

    got it Rudy did my allis I forgot how to find him tks
  15. C

    J D 1.5 E restored from N Dakota--need mag re magnetized

    after finishing with complete restore on the engine from Upham ND i find it wont start cause only 2 volts out of cheaned up Magneto . where can i send it to restore megnetisim please , just say down with dad in law (102 yrs old) and we went thru it at the home --he says its right but low...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top