(800) 853-2651
SHOP NOW

Recent content by cowdog

  1. C

    WTB engine or engine block

    WTB. I am looking for a Herules IXB 3 complete engine or a good block for my HG crawler. Thanks and Merry Christmas.. Call Dave @ 406 9fiveone zero 99seven
  2. C

    860 hydraulics/ 3 point lift

    I have an 860 ford . If I shut my tractor off and leave.the position control lever in the up position , when I start it a few hours or next day later it will lift the blade right away. However, if the postion co trolls lever is down and left down. When I start it up, it will take anywhere...
    • cowdog
    • Thread
    • Replies: 0
    • Forum: Ford
  3. C

    OT - Retired!

    I retired 10 months ago after 38 years with the same company. I have had no trouble staying busy. It's not hard to do. But I miss.the routine of a job. I dont want to work for some mouth breathing kid. So I a m starting my own excavation and dirt hauling service. Been busy getting all...
  4. C

    Big Bud 747

    I spent a summer breaking sod in the late seventies with a big bud kt450. It was a summer job on a dryland farm in southeastern Mt. It was about half the size of the 747, but it was still pretty darn big. It was a comfortable machine as long as everything worked on it.. One thing I really...
  5. C

    New 860 hydralic issues

    Ok. I got my hydraulic pump rebuilt. I.have bled the system many times. Including putting air pressure I to.the dipstick hole. It works up and down fine. The issue I have is this. If I leave the position control lever at the bottom of the quadrant when I shut it off overnite. When I start...
  6. C

    New 860 hydralic issues

    I think I understand what you are saying Hobo. But when I get into it I might have a question or two. So stay tuned please. Likely be after first of year before I get into it. Thanks Dave C
  7. C

    New 860 hydralic issues

    Ok, I will get it tore down after the holidays. Thanks fr tir help . I might have a few questions for you when I get into it. Thanks again and Merry Christmas Dave C
  8. C

    New 860 hydralic issues

    Ok, thanks guys. I will check the weather forecast and see if the weather will allow me to have it in the shop fr a bit. Are those valve springs easy to buy/ find?
  9. C

    New 860 hydralic issues

    Just upgraded to an 860. Wow!. It has a few issues though. When I start it up, it takes a few minutes before the 3 point raises. I did change the hydralic oil.. When it does raise, it kind of stutters as it goes up. It does however hold the back blade up for a long time . Lastly, the...
    • cowdog
    • Thread
    • Replies: 8
    • Forum: Ford
  10. C

    PROPANE TANK and regulator at the House

    Typically, the inlet of the 1st stage regulator is a POL fitting, as well as the service valve on the tank. They have left hand thread, . This is not an absolute , but typically how it is done today. The outlet to the 1st stage regulator is pipe thread. Either way, if it was hooked up...
  11. C

    PROPANE TANK and regulator at the House

    True, but not appropriate for this application. It would be indicative of a temp or sloppy install. IMHO.
  12. C

    PROPANE TANK and regulator at the House

    After being in the lp business for nearly 40 years I would do this. Get a new 1st stage regulator. Your regulator is fubar!. The 1st stage regulator should be RED in color. It takes tank pressure down to approx 10 psi. The 2nd stage regulator at the house should be GREEN . It takes the 10...
  13. C

    Propane Tank hookup

    The copper pigtail that goes from tank to the regulator can be bought in longer lengths.. tThat will give you some slack for your line to the house . Yes the poly pipe has a riser with a steel coax for the poly pipe where it comes above ground. If you ever choose to replace it.
  14. C

    Propane Tank hookup

    I retired from the fuel and lp business last spring after 38 years. Copper is fine. Don't screw with it. If you do anything, replace ALL of it with the poly yellow pipe. It will last longer than nuclear waste. Have your lp supplier do the work. They do it every day .
  15. J

    JI case model 10 trailing mower parts

    Hey everybody. First post on this site. I'm looking for a knife bar for my ji case model 10 trailing mower with a 7 foot cutter bar. Also, any leads on a parts and a repair manual would be great. Any help is greatly appreciated.
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top